Already a subscriber? 
MADCAD.com Free Trial
Sign up for a 3 day free trial to explore the MADCAD.com interface, PLUS access the
2009 International Building Code to see how it all works.
If you like to setup a quick demo, let us know at support@madcad.com
or +1 800.798.9296 and we will be happy to schedule a webinar for you.
Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?
AWWA C216-22 Heat-Shrinkable Cross-Linked Polyolefin Coatings for Steel Water Pipe and Fittings, 2022
- Foreword [Go to Page]
- I. Introduction. [Go to Page]
- I.A. Background. Heat-shrinkable cross-linked polyolefin coatings for external use on special sections, connections, and fittings for underground steel water pipelines have been used since 1960. This standard establishes required performance standards for [Go to Page]
- I.B. History. The first edition of this standard was approved by the AWWA Board of Directors on Jan. 29, 1989, and had an effective date of July 1, 1989. Subsequent editions were approved on June 19, 1994, with an effective date of Aug. 1, 1995; on Jan. 2
- II. Special Issues. [Go to Page]
- II.A. General. ANSI/AWWA C216 is intended to govern the exterior coating of special sections, connections, and fittings for underground steel water pipelines. These types of coatings are generally used on pipe that has been coated before transportation to [Go to Page]
- II.B. Weld-After-Backfill. Weld-after-backfill is the sequence of assembling a welded joint, tack welding the outside joint, applying the exterior joint coating(s), backfilling the pipe joint, and then welding the inside joint at a later time (where inter
- III. Use of This Standard. It is the responsibility of the user of an AWWA standard to determine that the products described in that standard are suitable for use in the particular application being considered. [Go to Page]
- III.A. Purchaser Options and Alternatives. The following items should be included by the purchaser:
- IV. Major Revisions. Major changes made to the standard in this edition are as follows:
- V. Comments. If you have any comments or questions about this standard, please call AWWA Engineering and Technical Services at 303.794.7711; FAX at 303.795.7603; write to the department at 6666 West Quincy Avenue, Denver, CO 80235-3098; or email at standa
- AWWA Standard
- SECTION 1: GENERAL
- Sec. 1.1 Scope
- Sec. 1.2 Purpose
- Sec. 1.3 Application
- SECTION 2: REFERENCES
- SECTION 3: DEFINITIONS
- SECTION 4: REQUIREMENTS
- Sec. 4.1 Equipment
- Sec. 4.2 Materials and Workmanship
- Sec. 4.3 Coating System
- Sec. 4.4 Surface Preparation
- Sec. 4.5 Coating Application (Field and Shop)
- Sec. 4.6 Coating Repair
- Sec. 4.7 Field Procedures
- SECTION 5: VERIFICATION
- Sec. 5.1 Coating Materials Prequalification
- Sec. 5.2 Prequalification Requirements of Coating System [Go to Page]
- Table 1 Prequalification requirements of coating system
- Sec. 5.3 Quality Assurance and Records
- Sec. 5.4 Inspection and Testing by the Purchaser
- Sec. 5.5 Quality Control Requirements of Applied Coating System
- Sec. 5.6 Rejection
- SECTION 6: DELIVERY
- Sec. 6.1 Marking
- Sec. 6.2 Packaging and Shipping
- Sec. 6.3 Affidavit of Compliance [Go to Page]
