Cart (0)
  • No items in cart.
Total
$0
There is a technical issue about last added item. You can click "Report to us" button to let us know and we resolve the issue and return back to you or you can continue without last item via click to continue button.
Home
Content
Tour
eLibrary
Store
Search book title
Filters:
FORMAT
BOOKS
All Books
PACKAGES
All Packages
EDITION
to
PUBLISHER
AABC
(1)
AAMI
(338)
ACI
(589)
AISC
(55)
ASA
(234)
ASCE
(996)
ASHRAE
(690)
ASME
(2161)
ASSE
(117)
ASTM
(94958)
AWC
(58)
AWWA
(575)
BHMA
(124)
BICSI
(33)
BIFMA
(21)
BOMA
(20)
BSI
(95391)
CHD
(3)
CRSI
(17)
IAHSS
(1)
IAPMO
(374)
ICC
(319)
IEEE
(6732)
IES
(241)
ISEA
(16)
Joint Commission
(184)
Joint Commission Int.
(1)
NETA
(6)
NFPA
(1667)
TCNA
(17)
TMS
(19)
USGBC
(28)
WILEY
(4)
 
AR
(6)
AZ
(7)
CA
(115)
CT
(3)
FL
(57)
ID
(5)
IL
(5)
IN
(1)
KY
(1)
LA
(2)
MI
(25)
MN
(27)
NC
(27)
NJ
(13)
NY
(61)
OH
(24)
OR
(22)
PA
(7)
RI
(8)
SC
(20)
SD
(1)
TX
(3)
VA
(50)
VT
(6)
WA
(33)
CONTENT TYPE
 Act
 Admin Code
 Announcements
 Bill
 Book
 CADD File
 CAN
 CEU
 Charter
 Checklist
 City Code
 Code
 Commentary
 Comprehensive Plan
 Conference Paper
 County Code
 Course
 DHS Documents
 Document
 Errata
 Executive Regulation
 Federal Guideline
 Firm Content
 Guideline
 Handbook
 Interpretation
 Journal
 Land Use and Development
 Law
 Legislative Rule
 Local Amendment
 Local Code
 Local Document
 Local Regulation
 Local Standards
 Manual
 Model Code
 Model Standard
 Notice
 Ordinance
 Other
 Paperback
 PASS
 Periodicals
 PIN
 Plan
 Policy
 Product
 Product - Data Sheet
 Program
 Provisions
 Requirements
 Revisions
 Rules & Regulations
 Standards
 State Amendment
 State Code
 State Manual
 State Plan
 State Standards
 Statute
 Study Guide
 Supplement
 Sustainability
 Technical Bulletin
 All
  • BSI
    PD CEN/TS 14807:2013 Plastics piping systems. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). Guidance for the structural analysis of buried GRP-UP pipelines
    Edition: 2013
    $313.97
    / user per year

Description of PD CEN/TS 14807:2013 2013

This Technical Specification, which is a guidance document for use with a structural analy sis procedure for below ground installations, covers limits applicable to glass -reinforced thermosetting plastics (GRP) pipes used for the conveyance of liquids under pressure or gravity conditions.

This document does not specify a particular structural analysis procedure but gives guidance on the selection of a structural analysis procedure. It concludes that any established structural analysis procedure may be used provided it includes the assessment of short and long -term deflection and buckling resistan ce.

Products complying to the applicable GRP product standards EN 1796 or EN 14364, which are not subject to internal pressure, are suitable as long as the analysis shows that the long -term deflection of the installed pipes is limited to 6 %, which is the basic assumption of the GRP pipe product standards. Products complying with the applicable system standards (EN 1796 or EN 14364), which are subject to internal pressure, are suitable as long as the analysis shows that the initial deflection of the installed pipes does not exceed 3 %.

NOTE The approach followed when preparing a general structural analysis procedure does not depend on the nominal size(s) of the pipe(s).

A suitable structural analysis procedure should normally be capable of being used for pipes operatin g at different temperatures provided that the corresponding temperature re -rating factors for the relevant pipe properties are applied, as specified in the referring standard(s). Nevertheless, high service temperatures may require an additional analysis of the longitudinal stresses and strains and/or a special design of the joints.

Normal structural analysis procedures are intended to cover normal soil installation conditions. Pipes to be designed for installations in abnormal or unusual conditions, e.g. in quick soils or a marine sea-bed, may require special engineering. Some structural analysis procedures may include axial effects depending upon the type of joint used.



Standard NumberPD CEN/TS 14807:2013
TitlePlastics piping systems. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). Guidance for the structural analysis of buried GRP-UP pipelines
StatusDefinitive
Publication Date2013-12-31
Identical National Standard OfCEN/TS 14807:2013
DescriptorsThermosetting polymers, Drainage, Reinforced materials, Wear tests, Sewerage, Polyesters, Plastics, Unsaturated polyesters, Glass fibres, Pipework systems, Abrasion testing, Pipes, Sewers
ICS93.030 External sewage systems, 91.140.60 Water supply systems, 91.140.80 Drainage systems
CommitteePRI/88
ISBN978 0 580 82218 6
PublisherBSI
Pages16

About BSI

BSI Group, also known as the British Standards Institution is the national standards body of the United Kingdom. BSI produces technical standards on a wide range of products and services and also supplies certification and standards-related services to businesses.
GROUPS
X