Cart (0)
  • No items in cart.
Total
$0
There is a technical issue about last added item. You can click "Report to us" button to let us know and we resolve the issue and return back to you or you can continue without last item via click to continue button.
Home
Content
Tour
eLibrary
Store
Search book title
Filters:
FORMAT
BOOKS
All Books
PACKAGES
All Packages
EDITION
to
PUBLISHER
AABC
(1)
AAMI
(337)
ACI
(589)
AISC
(55)
ASA
(234)
ASCE
(996)
ASHRAE
(690)
ASME
(2161)
ASSE
(117)
ASTM
(94624)
AWC
(54)
AWWA
(575)
BHMA
(124)
BICSI
(33)
BIFMA
(21)
BOMA
(20)
BSI
(94991)
CHD
(3)
CRSI
(17)
IAHSS
(1)
IAPMO
(374)
ICC
(315)
IEEE
(6731)
IES
(241)
ISEA
(16)
Joint Commission
(184)
Joint Commission Int.
(1)
NETA
(6)
NFPA
(1667)
TCNA
(17)
TMS
(19)
USGBC
(28)
WILEY
(4)
 
AR
(6)
AZ
(7)
CA
(115)
CT
(3)
FL
(57)
ID
(5)
IL
(5)
IN
(1)
KY
(1)
LA
(2)
MI
(25)
MN
(27)
NC
(27)
NJ
(13)
NY
(61)
OH
(24)
OR
(22)
PA
(7)
RI
(8)
SC
(20)
SD
(1)
TX
(3)
VA
(50)
VT
(6)
WA
(33)
CONTENT TYPE
 Act
 Admin Code
 Announcements
 Bill
 Book
 CADD File
 CAN
 CEU
 Charter
 Checklist
 City Code
 Code
 Commentary
 Comprehensive Plan
 Conference Paper
 County Code
 Course
 DHS Documents
 Document
 Errata
 Executive Regulation
 Federal Guideline
 Firm Content
 Guideline
 Handbook
 Interpretation
 Journal
 Land Use and Development
 Law
 Legislative Rule
 Local Amendment
 Local Code
 Local Document
 Local Regulation
 Local Standards
 Manual
 Model Code
 Model Standard
 Notice
 Ordinance
 Other
 Paperback
 PASS
 Periodicals
 PIN
 Plan
 Policy
 Product
 Product - Data Sheet
 Program
 Provisions
 Requirements
 Revisions
 Rules & Regulations
 Standards
 State Amendment
 State Code
 State Manual
 State Plan
 State Standards
 Statute
 Study Guide
 Supplement
 Sustainability
 Technical Bulletin
 All
  • BSI
    BS 4999-145:1987 General requirements for rotating electrical machines - Specification for winding terminations
    Edition: 1987
    $281.30
    / user per year

Description of BS 4999-145:1987 1987

This part of this British Standard specifies types of and performance requirements for winding terminations for rotating electrical machines rated for a.c. voltages up to 15 kV r.m.s. Minimum creepage and clearance distances appropriate to the rated voltages are also specified.

This standard does not specify requirements for the ability of the terminations of the following machines to withstand a high energy fault:

  1. machines rated for voltages up to and including 660 V, which it is assumed, would be protected by fuses or other energy limiting devices.
  2. machines rated for voltages of 1 100 V and above either protected by fuses or other energy limiting devices or intended for operation on a system where the nominal short-circuit capacity is lower than the relevant value given in Table 1.

The standard applies to terminals, terminal boxes and terminal enclosures, but it does not specify requirements for flameproof terminal enclosures.

The choice of a particular termination will be largely governed by the service and environmental conditions, but the standard is also relevant to the various types of cables normally used, including aluminium and, where applicable, cable sealing and dividing boxes. It is outside the scope of this British Standard to cover external supply cables in detail, but insofar as the design of the terminals is concerned, essential data are listed.

Winding terminations for small power machines having rated outputs up to and including 0.75 kW or kV·A per 1 000 r/min, such as those specified in BS 5000-11, are not covered by this standard.

NOTE The titles of the publications referred to in this standard are listed on the inside back cover.



Specifies terminations for rotating machines rated up to 15 kV a.c. r.m.s. Types of terminations. Creepage and clearance distances, current ratings of connections, definitions.

Standard NumberBS 4999-145:1987
TitleGeneral requirements for rotating electrical machines - Specification for winding terminations
StatusConfirmed
Publication Date1987-02-27
ReplacesBS 4999-71:1984
DescriptorsWindings, Cable junctions, Performance, Fault currents, Leakage paths, Electric enclosures, Electric machines, Alternating-current machines, Electric terminals, Rated voltage, Clearance distances, Rotating electric machines, Boxes (electric)
ICS29.160.01 Rotating machinery in general
CommitteePEL/2
ISBN0 580 15784 9
PublisherBSI
Pages10

About BSI

BSI Group, also known as the British Standards Institution is the national standards body of the United Kingdom. BSI produces technical standards on a wide range of products and services and also supplies certification and standards-related services to businesses.
GROUPS
X