FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F467 2013ASTM F467 - 13Standard Specification for Nonferrous Nuts for General UseActive Standard ASTM F467 | Developed by Subcommittee: F16.04 Book of Standards Volume: 01.08 ASTM F467Abstract This specification covers the requirements for commercial wrought nonferrous nuts in nominal thread diameters M6 to M36 inclusive in a number of alloys in common use and intended for general service applications. Materials shall be tested and shall conform to the chemical composition, hardness, proof stress, proof load, and tensile stress requirements. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Significance and Use 11.1 For purposes of determining compliance with the specified limits for requirements of the properties listed in this specification, an observed value or calculated value shall be rounded in accordance with Practice E29 . 1. Scope 1.1 This specification covers the requirements for commercial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in diameter in a number of alloys in common use and intended for general service applications. 1.2 Applicable bolts, cap screws, and studs for use with nuts covered by this specification are covered by Specification F468 . 1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
Note 1 This specification is the inch-pound companion to Specification F467M; therefore, no SI equivalents are
presented in the specification.
ASTM Standards B154 Test Method for Mercurous Nitrate Test for Copper Alloys B574 Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod D3951 Practice for Commercial Packaging E18 Test Methods for Rockwell Hardness of Metallic Materials E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications E34 Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys E38 Methods for Chemical Analysis of Nickel-Chromium and Nickel-Chromium-Iron Alloys E53 Test Method for Determination of Copper in Unalloyed Copper by Gravimetry E54 Test Methods for Chemical Analysis of Special Brasses and Bronzes E55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods) E75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys E76 Test Methods for Chemical Analysis of Nickel-Copper Alloys E92 Test Method for Vickers Hardness of Metallic Materials E101 Test Method for Spectrographic Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane Technique E120 Test Methods for Chemical Analysis of Titanium and Titanium Alloys E165 Practice for Liquid Penetrant Examination for General Industry E227 Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane Technique E354 Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys E478 Test Methods for Chemical Analysis of Copper Alloys E1409 Test Method for Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by the Inert Gas Fusion Technique F468 Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use F606 Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets F1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection ASME Standards B 18.2.2 Square and Hex NutsKeywords ?general use; nonferrous; nuts ; ICS Code ICS Number Code 21.060.20 (Nuts) DOI: 10.1520/F0467-13 ASTM International is a member of CrossRef. ASTM F467The following editions for this book are also available...
This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|