|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F3618 2022ASTM F3618-22Active Standard: Standard Practice for Cleaning of Thermoplastic Solid Wall Sanitary Sewer PipelinesASTM F3618Scope 1.1 This practice covers the personnel requirements, operator training, Environmental Protection Agency (EPA) Guidelines, operating procedures, and recommended equipment performance/design for the proper operation of pressure water-jet cleaning and cutting equipment as normally used by municipalities and contractors concerned with operations, maintenance, and cleaning work of Municipal Thermoplastic gravity sewer pipe. 1.2 The term high-pressure water jetting within this practice covers all water jetting, including the use of jets and hydro mechanical tooling at pressures below 2000 psi (0.69 MPa). 1.3 This practice covers the high-pressure water jetting of Thermoplastic pipe and should not be applied to other pipe and pipe-lining materials without evaluating the recommended cleaning procedure from the pipe manufacturer to avoid damage. 1.4 This practice applies to High-Density Polyethylene, Polypropylene, and Polyvinyl Chloride (HDPE, PP, and PVC) Thermoplastic sewer pipe manufactured in accordance with ASTM Standards. It may also be considered for use for any similar thermoplastic pipe products not covered by this list but with similar performance characteristics. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 5 on Hazards/Safety. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords high-velocity water cleaning; hydro flush; mechanical cleaning; nozzle; pipelines; power rodder; proofing skid; safety; sanitary sewer; sewer; sewer cleaning; sewer spill prevention; standard operating procedure; water-jetting equipment; ICS Code ICS Number Code 23.040.20 (Plastics pipes) DOI: 10.1520/F3618-22 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|