|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F3607 2022ASTM F3607-22Active Standard: Standard Specification for Additive Manufacturing – Finished Part Properties – Maraging Steel via Powder Bed FusionASTM F3607Scope 1.1 This specification covers additive manufacturing of parts via full-melt laser beam powder bed fusion (PBF-LB) processing of maraging steel alloys. Parts made using this processing method are typically used in applications that require mechanical properties similar to wrought products, either as fabricated or heat treated. Products built to this specification may require additional post-processing in the form of machining, polishing, etc., to meet necessary surface finish and dimensional requirements. 1.2 Maraging steel (MS) is a class of precipitation hardened steel, where aging heat treatment is used to form precipitates and, consequently, achieve significantly increased hardness and strength. This specification focuses specifically on 300 grade maraging steel, which corresponds to UNS K93120 and EN1.2709. MS grade 300 has higher concentrations of cobalt and titanium than lower grades. 1.3 This specification is intended for the use of purchasers or producers, or both, of additively manufactured maraging steel parts for defining the requirements and ensuring part properties. 1.4 Users are advised to use this specification as a basis for obtaining parts that will meet the minimum acceptance requirements established and revised by consensus of committee members. 1.5 User requirements considered more stringent may be met by the addition to the purchase order of one or more supplementary requirements, which include, but are not limited to, those listed in Supplementary Requirements in Sections S1 to S3. 1.6 The values stated in SI units are to be regarded as standard. All units of measure included in this guide are accepted for use with the SI. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords additive manufacturing; maraging steel; PBF-LB; powder bed fusion; ICS Code ICS Number Code 25.030 (Additive manufacturing) DOI: 10.1520/F3607-22 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|