|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F3423/F3423M 2022ASTM F3423/F3423M-22Active Standard: Standard Specification for Vertiport DesignASTM F3423/F3423MScope 1.1 This specification defines the requirements for the planning, design, and establishment of vertiports intended to service vertical takeoff and landing (VTOL) aircraft. These aircraft include, but are not limited to, standard category aircraft, optionally piloted aircraft, and unmanned aircraft. Aircraft not covered by this specification include VTOL aircraft less than 55 lb [25 kg]. In developing these standards, identified types of eVTOL aircraft, for example, Multi-Rotor, Lift & Cruise, Vectored Thrust, Tilt Wing, Tilt Rotor, etc., were considered. Ultimately it is up to the authorities having jurisdiction (AHJ) as to how and to what extent these standards are applied. Vertiports may provide commercial or private services in support of the operation of eVTOL aircraft including, but not limited to, some or all of occupant and cargo transport, air medical, flight instruction, aerial work, aircraft rental, fueling, charging of energy storage devices, battery exchange, hangaring, and maintenance services. 1.2 This specification is intended to support the design of civil vertiports and vertistops, however, it may also be used as a best practice document for other facilities. 1.2.1 Vertiport is a generic reference to the area of land, water, or structure used, or intended to be used, for the landing and takeoff of VTOL aircraft, together with associated buildings and facilities. At this time, aircraft with floats conducting water landings and takeoffs are not included in this specification. 1.2.2 Vertistop—The same as Vertiport, except that no fueling, defueling, scheduled maintenance, scheduled repairs, or storage of aircraft is permitted. Unscheduled maintenance and repairs to return an aircraft in an AOG (Aircraft on Ground) status to a serviceable status are permissible. 1.3 This document may present information in either SI units, English Engineering units, or both. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords eAircraft; electric aircraft; hybrid aircraft; UAM; UAS; urban air mobility; unmanned aircraft system; vertical takeoff and landing; vertiport; vertistop; VTOL; ICS Code ICS Number Code 49.020 (Aircraft and space vehicles in general) DOI: 10.1520/F3423_F3423M-22 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|