|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F3314 2024ASTM F3314-24Redline Standard: Standard Terminology Relating to Technology and Underground InfrastructureASTM F3314Scope 1.1 This terminology is a compilation of definitions of technical terms used in the underground infrastructure and plastic piping industry. Terms that are generally understood or adequately defined in other readily available sources are not included. 1.2 When a term is used in an ASTM document for which Committee F36 is responsible, it is included only when judged, after review, by Subcommittee F36.91 to be a generally usable term. 1.3 Definitions that are identical to those published by other ASTM committees or other standards organizations are identified with the committee number (for example, F17) or with the abbreviation of the name of the organization (for example, IUPAC, International Union of Pure and Applied Chemistry). 1.4 A definition is a single sentence with additional information included in discussions. 1.5 Definitions are followed by the committee responsible for the standard(s) (for example, [F36.10]) and standard numbers(s) in which they are used (for example, F2233). 1.6 Abbreviated Terminology: 1.6.1 Abbreviated terminology is intended to provide uniform contractions of terms relating to infrastructure that have evolved through widespread common usage. The compilation in this standard has been prepared to avoid the occurrence of more than one abbreviated term for a given term and to avoid multiple meanings for abbreviated terms. 1.6.2 The abbreviated terminology and descriptions in this standard are intended to be consistent with usage in the infrastructure industry and the standards under F36 jurisdiction. Other ASTM committees may assign a different word-phrase description to the same abbreviated terminology. In such cases, the abbreviated terms in this standard shall apply to usage in F36 standards, or if widespread misunderstanding could result from conflicting abbreviated terminology descriptions, the abbreviated terminology for the word-phrase shall not be used in F36 standards. 1.6.3 Acronyms and Initialisms—A word formed from the letters or parts of words of a longer word-phrase, usually from the initial letters or parts of the words. An acronym is pronounced as a word, for example, radar for radio detection and ranging. An initialism is pronounced as a series of letters, for example, DOT for Department of Transportation. 1.6.4 The acronym or initialism description is the origin word-phrase for the acronym or initialism, not a definition. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords brush-in-place pipe (BIPP); cleanout; closed circuit television (CCTV); geopolymer; lining, non-structural; lining, structural; maintenance hole (MH); manhole; microbial induced corrosion (MIC); pozzolan; spray-in-place pipe (SIPP); ICS Code ICS Number Code 01.040.93 (Civil engineering (Vocabularies)) DOI: 10.1520/F3314-24 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|