|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F3214 2023ASTM F3214-23Redline Standard: Standard Practice for Characterization of Fire Properties of Seating, Upholstery, and Padding Materials for Vehicles Associated with Amusement Rides and DevicesASTM F3214Scope 1.1 This practice describes the required smoldering ignition fire properties for seating, upholstery, and padding materials used for vehicles associated with amusement rides and devices. 1.2 This practice includes an annex with an example of an optional open flame test method for padding materials. 1.3 This practice also contains a non-mandatory appendix with optional guidance for the procedure to follow in the event that an optional fire hazard analysis is to be conducted for vehicles used on amusement rides and devices. 1.3.1 In the event that such a fire hazard analysis is to be conducted, it needs to include considerations related to heat release, smoldering, and flaming ignition, flame spread and smoke release. 1.3.2 The appendix contains specific recommendations of standardized fire test methods that are suitable (but not required) for determining material properties related to heat release rates, smoldering, and flaming ignition, flammability, and smoke release for materials. 1.4 This practice is not a fire test method. 1.5 This practice does not require the conduction of a fire hazard analysis. 1.6 This practice does not address the use of active fire protection measures, such as fire sprinklers, or smoke, fire, or heat detectors. 1.7 This practice does not address the probability of any fire scenario associated with amusement rides or devices resulting in a hazardous event. Thus, this practice does not address the potential risk associated with any fire scenario. Practice F2291-21 includes general requirement to assess and mitigate hazards for all rides and devices. 1.8 This practice shall not apply to: 1.8.1 Materials specified for amusement rides or devices other than those associated specifically with the ride vehicle assembly. 1.8.2 Materials used for the construction of facilities. 1.8.3 Fluids and lubricants. 1.8.4 Vehicles used on water slides or other aquatic devices. 1.9 The values stated in SI units, see IEEE/ASTM SI-10-16, are to be regarded as standard. The values given in parentheses, if any, after SI units are provided for information only and are not considered standard. 1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords amusement ride; device; fire; fire hazard analysis; heat release; ignition; smoke release; smoldering; ICS Code ICS Number Code 13.220.50 (Fire-resistance of building materials and elements) DOI: 10.1520/F3214-23 The following editions for this book are also available...
This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|