ASTM F2562/F2562M-07
Historical Standard: ASTM F2562/F2562M-07 Standard Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage
SUPERSEDED (see Active link, below)
ASTM F2562 / F2562M
1. Scope
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, impact resistance, pipe stiffness, flattening, buckling, tensile strength of seam, joint systems, perforations, and markings for steel reinforced thermoplastic pipe and fittings of nominal sizes 8 in. [200 mm] through 120 in. [3000 mm]. The steel reinforced, spirally formed thermoplastic pipes governed by this standard are intended for use in underground applications where soil provides support for their flexible walls. These pipes will be used for gravity flow and non-pressure applications, such as storm sewers, sanitary sewers, industrial waste applications and drainage pipes.
1.2 Units The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text the SI units are shown in brackets. The values stated in each system may not be exact equivalents: therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4 There is no similar or equivalent ISO standard.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
A1008/A1008M Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake Hardenable
A1011/A1011M Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials
F412 Terminology Relating to Plastic Piping Systems
F477 Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
F2136 Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe
Military Standards
MIL-STD-129 Marking for Shipment and StorageAmerican Association of State Highway and Transportation Officials (AASHTO)
AASHTOM294-05 Corrugated Polyethylene Pipe, 300- to 1500-mm DiameterFederal Standards
Fed.Std.No.123 Marking for Shipment (Civil Agencies)Keywords
Helically formed; Steel reinforced; ribbed pipe; polyethylene; pipe; Drainage pipe; Nonpressure piping--specifications; Pipe fittings--steel; Pipe fittings--thermoplastic; Sewer fittings; Sewer pipe; Steel pipe--specifications; Steel pipe fittings; Steel pipe (sewers and drainage systems); Thermoplastic pipe/tube/fittings;
ICS Code
ICS Number Code 93.030 (External sewerage systems)
DOI: 10.1520/F2562_F2562M-07
ASTM International is a member of CrossRef.