Abstract

This specification deals with fabricated fittings intended for use with outside-diameter controlled polyethylene pipe and tubing. These fittings are manufactured by heat-fusion joining shape-modified polyethylene components prepared from pipe, molded fittings, sheet, or block. Pressure rating of the fabricated-fitting design is beyond the scope of this standard and shall be established by the fitting manufacturer. This specification includes requirements for both room temperature and elevated temperature pressure-tests to demonstrate a reasonable level of performance of the fabricated-fitting design at the pressure rating established by the fitting manufacturer. Materials shall be tested and shall conform to the requirements for materials, design, workmanship, minimum dimensions, marking, test methods, and quality control.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification establishes requirements for fabricated fittings intended for use with outside-diameter controlled polyethylene pipe and tubing. These fittings are manufactured by heat-fusion joining shape-modified polyethylene components prepared from pipe, molded fittings, sheet, or block. Included are requirements for materials, design, workmanship, minimum dimensions, marking, test methods, and quality control.

1.2 Pressure rating of the fabricated-fitting design is beyond the scope of this standard and shall be established by the fitting manufacturer. This specification includes requirements for both elevated temperature pressure-tests and short-term pressurization tests to demonstrate a reasonable level of performance of the fabricated-fitting design at the pressure rating established by the fitting manufacturer.

1.3 The pressure-tests requirements are specified by the fittings equivalent (E) DR. The EDR specified is the DR of the piping system for which the fabricated fitting is intended to be butt-fused.

1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

1.5 Units The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard.

1.6 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D1600 Terminology for Abbreviated Terms Relating to Plastics

D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

D2513 Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings

D3035 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter

D3261 Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing

F412 Terminology Relating to Plastic Piping Systems

F714 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter

F2619/F2619M Specification for High-Density Polyethylene (PE) Line Pipe

F2880 Specification For Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes 3/4 in. to 65 in.

Federal Standards

ANSI/NSF Standard

Plastic Pipe Institute

Military Standard

Keywords

fabricated fittings; polyethylene; Block stock; Butt heat fusion fittings; Fabricated fittings; Plastic pipe/tubing/fittings--specifications; Polyethylene (PE) pipe--specifications;

ICS Code

ICS Number Code 23.040.20 (Plastic pipes); 23.040.45 (Plastic fittings)

DOI: 10.1520/F2206-11

ASTM International is a member of CrossRef.

ASTM F2206