1. Scope

1.1 This guide is a resource of currently available test methods for the characterization of biomaterial scaffolds used to develop and manufacture tissue-engineered medical products (TEMPs).

1.2 The test methods contained herein guide characterization of the bulk physical, chemical, mechanical, and surface properties of a scaffold construct. Such properties may be important for the success of a TEMP, especially if they affect cell retention, activity and organization, the delivery of bioactive agents, or the biocompatibility and bioactivity within the final product.

1.3 This guide may be used as guidance in the selection of appropriate test methods for the generation of a raw material or original equipment manufacture (OEM) specification. This guide also may be used to characterize the scaffold component of a finished medical product.

1.4 This guide addresses natural, synthetic, or combination scaffold materials with or without bioactive agents or biological activity. This guide does not address the characterization or release profiles of any biomolecules, cells, drugs, or bioactive agents that are used in combination with the scaffold.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D412 Test Methods for Vulcanized Rubber and Thermoplastic Elastomers--Tension

D570 Test Method for Water Absorption of Plastics

D638 Test Method for Tensile Properties of Plastics

D648 Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position

D671 Test Method for Flexural Fatigue of Plastics by Constant-Amplitude-of-Force

D695 Test Method for Compressive Properties of Rigid Plastics

D747 Test Method for Apparent Bending Modulus of Plastics by Means of a Cantilever Beam

D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials

D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement

D882 Test Method for Tensile Properties of Thin Plastic Sheeting

D1042 Test Method for Linear Dimensional Changes of Plastics Under Accelerated Service Conditions

D1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer

D1388 Test Method for Stiffness of Fabrics

D1621 Test Method for Compressive Properties of Rigid Cellular Plastics

D1623 Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics

D1708 Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens

D2857 Practice for Dilute Solution Viscosity of Polymers

D2873 Test Method for Interior Porosity of Poly(Vinyl Chloride) (PVC) Resins by Mercury Intrusion Porosimetry

D2990 Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics

D3016 Practice for Use of Liquid Exclusion Chromatography Terms and Relationships

D3039/D3039M Test Method for Tensile Properties of Polymer Matrix Composite Materials

D3417 Test Method for Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry (DSC)

D3418 Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry

D4001 Test Method for Determination of Weight-Average Molecular Weight of Polymers By Light Scattering

D4404 Test Method for Determination of Pore Volume and Pore Volume Distribution of Soil and Rock by Mercury Intrusion Porosimetry

D4603 Test Method for Determining Inherent Viscosity of Poly(Ethylene Terephthalate) (PET) by Glass Capillary Viscometer

D5226 Practice for Dissolving Polymer Materials

D5296 Test Method for Molecular Weight Averages and Molecular Weight Distribution of Polystyrene by High Performance Size-Exclusion Chromatography

D5732 Test Method for Stiffness of Nonwoven Fabrics Using the Cantilever Test

D6125 Test Method for Bending Resistance of Paper and Paperboard (Gurley Type Tester)

D6420 Test Method for Determination of Gaseous Organic Compounds by Direct Interface Gas Chromatography-Mass Spectrometry

D6474 Test Method for Determining Molecular Weight Distribution and Molecular Weight Averages of Polyolefins by High Temperature Gel Permeation Chromatography

D6539 Test Method for Measurement of Pneumatic Permeability of Partially Saturated Porous Materials by Flowing Air

D6579 Practice for Molecular Weight Averages and Molecular Weight Distribution of Hydrocarbon, Rosin and Terpene Resins by Size-Exclusion Chromatography

E128 Test Method for Maximum Pore Diameter and Permeability of Rigid Porous Filters for Laboratory Use

E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods

E456 Terminology Relating to Quality and Statistics

E473 Terminology Relating to Thermal Analysis and Rheology

E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

E793 Test Method for Enthalpies of Fusion and Crystallization by Differential Scanning Calorimetry

E794 Test Method for Melting And Crystallization Temperatures By Thermal Analysis

E967 Test Method for Temperature Calibration of Differential Scanning Calorimeters and Differential Thermal Analyzers

E968 Practice for Heat Flow Calibration of Differential Scanning Calorimeters

E996 Practice for Reporting Data in Auger Electron Spectroscopy and X-ray Photoelectron Spectroscopy

E1078 Guide for Specimen Preparation and Mounting in Surface Analysis

E1142 Terminology Relating to Thermophysical Properties

E1294 Test Method for Pore Size Characteristics of Membrane Filters Using Automated Liquid Porosimeter

E1298 Guide for Determination of Purity, Impurities, and Contaminants in Biological Drug Products

E1356 Test Method for Assignment of the Glass Transition Temperatures by Differential Scanning Calorimetry

E1642 Practice for General Techniques of Gas Chromatography Infrared (GC/IR) Analysis

E1829 Guide for Handling Specimens Prior to Surface Analysis

E1994 Practice for Use of Process Oriented AOQL and LTPD Sampling Plans

F151 Test Method for Residual Solvents in Flexible Barrier Materials

F316 Test Methods for Pore Size Characteristics of Membrane Filters by Bubble Point and Mean Flow Pore Test

F748 Practice for Selecting Generic Biological Test Methods for Materials and Devices

F1249 Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor

F1251 Terminology Relating to Polymeric Biomaterials in Medical and Surgical Devices

F1634 Practice for In-Vitro Environmental Conditioning of Polymer Matrix Composite Materials and Implant Devices

F1635 Test Method for in vitro Degradation Testing of Hydrolytically Degradable Polymer Resins and Fabricated Forms for Surgical Implants

F1884 Test Methods for Determining Residual Solvents in Packaging Materials

F1980 Guide for Accelerated Aging of Sterile Barrier Systems for Medical Devices

F1983 Practice for Assessment of Compatibility of Absorbable/Resorbable Biomaterials for Implant Applications

F2025 Practice for Gravimetric Measurement of Polymeric Components for Wear Assessment

F2027 Guide for Characterization and Testing of Raw or Starting Biomaterials for Tissue-Engineered Medical Products

F2312 Terminology Relating to Tissue Engineered Medical Products

F2450 Guide for Assessing Microstructure of Polymeric Scaffolds for Use in Tissue-Engineered Medical Products

G120 Practice for Determination of Soluble Residual Contamination by Soxhlet Extraction

AAMI Standards

Keywords

absorption; bioabsorption; biomaterials; biomedical material; bioresorption; cell seeding; matrix; porometry; porosimetry; porosity; scaffold; tissue engineering; Biomedical materials/applications; Cell seeding; Impurities--medical/surgical materials/applications; Matrix data/programs; Porosimetry; Porosity--medical/surgical materials; Scaffolds (medical); TEMPs (tissue engineered medical products);

ICS Code

ICS Number Code 11.020 (Medical sciences and health care facilities in general)

DOI: 10.1520/F2150-02E01

ASTM International is a member of CrossRef.