Abstract

This specification covers the requirements for non-pressure polyolefin pipe and fittings for corrosive waste drainage systems. The pipe is produced in Schedule 40 and 80 IPS sizes in two polyolefins (polyethylene and polypropylene) that shall contain suitable stabilizers and antioxidants and may contain pigments and fillers not detrimental to the pipe and fittings. The specimens shall conform to the outside diameter; wall thickness; average waterway diameter; chemical resistance to acetic acid, acetone, methyl alcohol, ammonium hydroxide, nitric acid, and sodium hydroxide; water absorption; system integrity; flattening; and impact resistance requirements. Hydrostatic pressure tests shall be conducted on both the heat-fused and mechanical joints.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification covers requirements for non-pressure polyolefin pipe and fittings for corrosive waste drainage systems.

1.2 Pipe is produced in Schedule 40 and 80 IPS sizes in two polyolefins, polyethylene (PE) and polypropylene (PP).

1.3 The interchangeability of pipe and fittings made by different manufacturers is not addressed in this specification. Transition fittings for joining pipe and fittings of different manufacturers is provided for in this specification.

1.4 Pipe and fittings are joined by the heat fusion method (D 2657 and F 1290) or by using mechanical joints recommended by the manufacturer.

1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.6 The following safety hazards caveat pertains only to the test method, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D543 Practices for Evaluating the Resistance of Plastics to Chemical Reagents

D570 Test Method for Water Absorption of Plastics

D618 Practice for Conditioning Plastics for Testing

D1248 Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable

D1600 Terminology for Abbreviated Terms Relating to Plastics

D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications

D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading

D2444 Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)

D2657 Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings

D3311 Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns

D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials

D4101 Specification for Polypropylene Injection and Extrusion Materials

F412 Terminology Relating to Plastic Piping Systems

F1290 Practice for Electrofusion Joining Polyolefin Pipe and Fittings

F1498 Specification for Taper Pipe Threads 60 for Thermoplastic Pipe and Fittings

Federal Standard

Military Standard

Other Document

Keywords

acid waste; corrosion resistance; corrosive waste; drainage; drain pipes; installation; joints; laboratory piped services; pipe fittings; pipes; plastic pipes; polyethylene; polyolefin; polypropylene; thermoplastic polymers; traps (drainage); waste disposal (building); Acid waste; Corrosive service applications--plastics; Drainage materials/systems--specifications; Installation--plastic pipe materials/applications; Laboratory piped services; Nonpressure piping--specifications; Polyethylene (PE) pipe--specifications; Polymers--specifications; Polyolefin (PO) pipe/fittings--specifications; Propylene (PP) plastics--specifications; Schedule 40/80/120 pipe; Thermoplastic pipe/tube/fittings--specifications; Traps (drainage); Waste disposal/drainage systems--specifications;

ICS Code

ICS Number Code 23.040.20 (Plastic pipes)

DOI: 10.1520/F1412-09

ASTM International is a member of CrossRef.

ASTM F1412