|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F1301 2024ASTM F1301-18-e1-Reapproved2024Active Standard: Standard Practice for Labeling Chemical Protective ClothingASTM F1301Scope 1.1 This practice covers the informational content of labels in or on chemical protective clothing. This practice also addresses putting label content on chemical protective clothing packaging when it is not practical to attach the label directly to the chemical protective clothing or print it on the chemical protective clothing item based on the size or type of the product. 1.2 This practice describes the recommended format and minimal content of the information to be included on the labels used for chemical protective clothing. 1.2.1 For the purposes of this practice, chemical protective clothing includes but is not limited to: suits, garments, and partial-body garments such as hoods, aprons, sleeve protectors, gloves, and footwear. 1.2.2 Protective clothing is defined as any single item or combination of items used for the purpose of isolating parts of the body from direct contact with a potential hazard. It does not include individual parts of a protective clothing item designed to be worn as part of another item (for example, a face shield or lens) unless it may be worn independently of the other items and still be used in a protective manner. For example, a glove or boot, unless permanently attached to a garment or suit, would be considered a protective clothing item requiring labeling, while a visor or vent valve would not. In summary, the intent of this practice is to only require labeling of parts of an ensemble that can be used independently for the protection of the user. 1.3 This practice does not cover user information provided by means other than item labeling such as instructions, informational packets, brochures, or other written means. User information is partly addressed in Practice F2061. 1.4 This practice excludes those items covered under 16 CFR 303 unless specifically designed for use as chemical protective clothing. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords chemical protective clothing; labeling; protective clothing ; ICS Code ICS Number Code 13.340.10 (Protective clothing) DOI: 10.1520/F1301-18R24E01 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|