|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-E3347/E3347M 2024ASTM E3347/E3347M-24Redline Standard: Standard Specification for Ballistic-Resistant Shields Used by Law Enforcement OfficersASTM E3347/E3347MScope 1.1 This standard specifies minimum performance requirements and test methods for the ballistic resistance of shields used by U.S. law enforcement officers to protect against handgun and rifle ammunition. 1.1.1 The option for testing either handgun-rated or rifle-rated shields with a shotgun threat is included in Appendix X3. Note 1: Shields rated as “shotgun only” are not typically produced in the industry because they are not used by law enforcement agencies. 1.2 Products addressed by this specification include hand-held or hand-carried shields (having single or multiple panels, multi-fold shields) and person-portable shields with wheels. 1.2.1 Shields may be stand-alone or may incorporate in conjunction with (ICW) armor appliques. 1.3 Products not addressed by this specification include fixed or mobile barriers not intended to move during an operation and flexible shields that drape across the surfaces upon which they are placed (for example, ballistic blankets). Note 2: The above products are addressed by Specification E3236/E3236M. 1.4 This specification addresses ballistic performance in terms of resistance to penetration (RTP) of the shield body, body edges, viewports, fasteners, and weak points. 1.5 Shields covered by this specification are classified into ASTM shield ballistic protection levels (see Section 10). 1.6 This specification is applicable for certification testing, verification testing, or research and development testing. 1.7 Values stated in either the International System of Units (metric) or U.S. Customary units [inch-pound] are to be regarded separately as standard. The values stated in each system may not be exact equivalents. Tests conducted using either system maintain repeatability and reproducibility of the test method and results are comparable. 1.8 This specification is divided into the following sections:
1.9 The tests required by this standard have inherent hazards. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords ballistic shield; ballistic-resistant shield; law enforcement ballistic shield; law enforcement equipment; ICS Code ICS Number Code 13.310 (Protection against crime) DOI: 10.1520/E3347_E3347M-24 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|