|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-E3281 2021ASTM E3281-21aActive Standard: Standard Guide for NAPL Mobility and Migration in Sediments – Screening Process to Categorize Samples for Laboratory NAPL Mobility TestingASTM E3281Scope 1.1 This guide is designed for general application at a wide range of sediment sites where non-aqueous phase liquid (NAPL) is present or suspected to be present in the sediment. This guide describes a process to use field screening methods, specifically visual observations, and the results of shake tests, to categorize the relative amount of NAPL present in a sample. This categorization can then be utilized to select co-located sediment samples for laboratory testing to determine if the NAPL in the sample interval is mobile or immobile at the pore scale, or any other chemical or physical testing. 1.1.1 There is no current industry standard methodology to select sediment samples for laboratory NAPL mobility testing; the use of different methodologies is possible. This guide focuses on a selection process that uses visual observations and shake tests. This process has the advantage of being simple to use and, if applied in a disciplined manner, has been demonstrated to provide good results in the field. 1.2 This guide is intended to inform, complement, and support characterization and remedial efforts performed under international, federal, state, and local environmental programs but not supersede local, state, federal, or international regulations. The users of this guide should review existing information and data available for a sediment site to determine applicable regulatory agency requirements and the most appropriate entry point into and use of this guide. 1.3 ASTM International (ASTM) standard guides are not regulations; they are consensus standard guides that may be followed voluntarily to support applicable regulatory requirements. This guide may be used in conjunction with other ASTM guides developed for assessing sediment sites. 1.4 This guide does not address methods and means of sample collection (Guide E3163). 1.5 Units—The values stated in SI or CGS units are to be regarded as the standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords contaminated sediments; field screening; laboratory NAPL mobility testing; mobility; NAPL; sediment; sediment corrective action; shake test; ICS Code ICS Number Code 13.080.01 (Soil quality and pedology in general) DOI: 10.1520/E3281-21A The following editions for this book are also available...
This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|