|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-E3113 2023ASTM E3113-23Active Standard: Standard Specification for Ballistic-resistant Vehicle Door Panels Used by Public Safety AgenciesASTM E3113Scope 1.1 This specification specifies requirements for ballistic-resistant panels to be mounted in or on public safety vehicle doors to protect against complete penetration of projectiles from small arms.2 1.2 The purpose of this specification is to define minimum performance for ballistic-resistant vehicle door panels. 1.2.1 In addition to the required tests, optional tests with specific conditions are provided that allow testing beyond the minimum requirements of this specification. Statements of conformance with this specification do not include any optional test unless the optional test is conducted, and the results are included in the test report. 1.3 This specification requires ballistic testing of vehicle door panels mounted either in a test fixture or mounted on a vehicle door for which the panel is designed. 1.3.1 Door panels intended to be mounted inside a vehicle door shall be assessed in a test fixture with air backing. 1.3.1.1 Two optional ballistic tests are provided for vehicle door panels intended to be mounted inside a vehicle door: (1) The preferred optional ballistic test assesses the panel in a vehicle door for which the panel is designed. (2) If a vehicle door for which the panel is designed is not available, a second optional ballistic test assesses the panel in a test fixture with air backing and a door skin simulant in front of the strike face of the panel. 1.3.2 Door panels intended to be mounted on the exterior of a vehicle door shall be assessed on a vehicle door for which the panel is designed. 1.3.3 An optional extreme temperature ballistic test is provided for purchasers concerned with performance of vehicle door panels in very hot or very cold environments. 1.3.4 The optional ballistic tests are provided in Appendix X1. 1.4 Selection and procurement guidance is provided in Appendix X2 to assist purchasers in using this specification to procure vehicles with ballistic-resistant door panels or to retrofit existing vehicles with ballistic-resistant door panels. 1.5 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to non-SI units that are provided for information only. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords ballistic; ballistic resistant vehicle door panel; vehicle door panel; ICS Code ICS Number Code 13.310 (Protection against crime) DOI: 10.1520/E3113-23 The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|