|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-E2616 2014ASTM E2616-09-Reapproved2014Historical Standard: Standard Guide for Remedy Selection Integrating Risk-Based Corrective Action and Non-Risk ConsiderationsASTM E2616Scope 1.1 This guide covers the selection of appropriate remedial actions at sites where a release of chemicals (for example, vapor-phase, dissolved-phase, or non-aqueous phase liquids (NAPL)) into the environment has occurred. This overall remedy selection process is illustrated in Fig. 1. The guide is intended to be applied within a risk-based corrective action (RBCA) framework. 1.5.1 Development of risk-based remedial action objectives that includes identification of complete exposure pathways and numeric remedial action levels (Section 5). 1.5.2 Development of non-risk remedial action objectives based on resource protection and other non-risk considerations. Resource protection objectives typically include numeric remedial action levels while other non-risk criteria are typically non-numeric and may include: remediation timeframe, implementability, cost effectiveness, regulatory compliance, property use requirements, liability control, and community concern (Section 5). 1.5.3 Evaluation of protectiveness to identify protective remedial actions that will be effective and timely for each risk-based remedial action objective for the site (Section 6). 1.5.4 Evaluation of the retained remedies using the non-risk remedial action objectives to identify acceptable remedial actions that satisfy the minimum level for each non-risk criterion (Section 7). 1.5.5 Remedial action selection to select the acceptable remedial action to be implemented at the site (Section 8). 1.5.6 Remedy design and implementation to ensure that the selected remedy is effectively implemented at the site and satisfies the remedial action objectives (Section 9). 1.6 This guide is intended for use in the selection of final remedial actions. This guide may also be used in the selection of interim measures provided that risk-based remedial action objectives and non-risk remedial action objectives are available for the evaluation of these interim measures. 1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.8 This guide is not intended to specifically address contractor health and safety issues. It is the responsibility of the user of this guide to ensure that Occupational Safety and Health Administration (OSHA) regulatory requirements are met,and appropriate industry practices are consulted for guidance. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Keywords ICS Code ICS Number Code 13.020.30 (Environmental impact assessment) DOI: 10.1520/E2616-09R14 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|