FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-E1924 2004ASTM E1924-97-Reapproved2004Historical Standard: Standard Guide for Conducting Toxicity Tests with Bioluminescent DinoflagellatesASTM E1924Scope 1.1 This guide covers two distinct procedures, based on similar principles, for obtaining data concerning the adverse effects of a test material (added to dilution water) on oceanic bioluminescent dinoflagellates. 1.1.1 The endpoint for both procedures is based on a measurable reduction or inhibition in light output from the dinoflagellates. Both procedures are similar in that when bioluminescent dinoflagellates are exposed to toxicants, a measurable reduction in bioluminescence is observed from their cells following mechanical stimulation when compared to control cells. In the first procedure, cells of the bioluminescent dinoflagellate Gonyaulax polyedra can be tested over a range of up to seven days of exposure (or longer) to a toxicant. The second procedure uses another species, Pyrocystis lunula, for a 4 h test. 1.2 Both procedures can measure the toxic effects of many chemicals, various marine and freshwater effluents, antifouling coatings, leachates, and sediments to bioluminescent dinoflagellates (1-5). Compounds with low water solubility such as large organic molecules may be solubilized with methanol, ethanol, and acetone solvents for testing (4) (see Guide E 729). 1.3 An IC50 in light output (bioluminescence) is the recommended endpoint (1). However, percent inhibition of bioluminescence is an appropriate endpoint in some cases (5). 1.4 Other modifications of these procedures might be justified by special needs or circumstances. Although using appropriate procedures is more important than following prescribed procedures, results of tests conducted using unusual procedures are not likely to be comparable to results of other tests. Comparison of results obtained using modified and unmodified versions of these procedures might provide useful information concerning new concepts and procedures for conducting acute and chronic tests. 1.5 The values stated in SI units are to be regarded as the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Keywords bioluminescence; dark phase; dinoflagellate; Gonyaulax Ployedra; inhibition; light output; Pyrocystis lanula; toxicity test ICS Code ICS Number Code 11.120.01 (Pharmaceutics in general) DOI: 10.1520/E1924-97R04 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|