Abstract

This specification is for nonmetallic honeycomb core used in the manufacture of adhesively bonded sandwich panels for tactical shelters. Five types of nonmetallic honeycomb material are specified: type I - honeycomb for use in panels which are required to have a high load-carrying capability that could not be adequately met using any of the other type; type II - honeycomb for use in panels which are required to have a load-carrying capability that could not be adequately met by using materials of any of types III, IV, or V; type III - honeycomb for general use in panels where the higher performances of types I, II, and IV materials are not required; type IV - honeycomb similar to type II but with slightly lower performance; and type V - honeycomb similar to type III but with slightly lower performance. The density, honeycomb core shear, honeycomb core compression, honeycomb core cyclic aging, honeycomb core brittleness impact, flatwise tensile, and pH shall be tested to meet the requirements prescribed. The fungus resistance test, thermal resistance test, shear modulus test, core compressive modulus test, water migration resistance test, flame resistance test, and dimensional examination shall be performed to meet the requirements prescribed.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification is for nonmetallic honeycomb core used in the manufacture of adhesively bonded sandwich panels for tactical shelters. The materials are intended for adhesive bonding to aluminum facings using materials and processes defined by Practices E 864 and E 874 and Specifications E 865 , E 866 , and E 990 . This specification covers five main types of honeycomb for use in sandwich panels, Types I, II, III, IV, and V. Types I, II, and III honeycombs correspond to three honeycomb densities. Types IV and V are similar to Types II and III, respectively, but have lower performance requirements.

1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units in parentheses are provided for information only. For conversion of quantities in various systems of measurement to SI units, refer to Practice E 380 .

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Other Publications

ASTM Standards

B209 Specification for Aluminum and Aluminum-Alloy Sheet and Plate

C177 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus

C366/C366M Test Methods for Measurement of Thickness of Sandwich Cores

C481 Test Method for Laboratory Aging of Sandwich Constructions

C518 Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus

D3951 Practice for Commercial Packaging

E864 Practice for Surface Preparation of Aluminum Alloys to Be Adhesively Bonded in Honeycomb Shelter Panels

E865 Specification for Structural Film Adhesives for Honeycomb Sandwich Panels

E866 Specification for Corrosion-Inhibiting Adhesive Primer for Aluminum Alloys to Be Adhesively Bonded in Honeycomb Shelter Panels

E874 Practice for Adhesive Bonding of Aluminum Facings to Nonmetallic Honeycomb Core for Shelter Panels

E990 Specification for Core-Splice Adhesive for Honeycomb Sandwich Structural Panels

E1749 Terminology Relating to Rigid Wall Relocatable Shelters

F501 Test Method for Aerospace Materials Response to Flame, with Vertical Test Specimen (for Aerospace Vehicles Standard Conditions)

Federal Aviation Regulation

Federal Standards

Military Standards

Keywords

adhesive bond; aluminum facing; honeycomb; honeycomb sandwich panels; nonmetallic honeycomb core; relocatable shelters; Adhesives (honeycomb core sandwich panels); Aluminum facings; Adhesion--honeycomb core sandwich panels; Adhesive bonds--specifications; Building materials/applications--specifications; Honeycomb shelter panels--specifications; Relocatable shelters--specifications; Shelters--specifications; Structural sandwich constructions--specifications;

ICS Code

ICS Number Code 91.060.20 (Roofs)

DOI: 10.1520/E1091-08

ASTM International is a member of CrossRef.

ASTM E1091