|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D8566 2024ASTM D8566-24Active Standard: Standard Specification for Glycol-Based Electric Vehicle Coolant with Low Electrical ConductivityASTM D8566Scope 1.1 This specification covers fully formulated glycol-based coolants with low electrical conductivity for use in electric vehicles (EV). 1.2 Coolants are formulated for cooling systems in battery electric vehicles (BEV), fuel cell electric vehicles (FCEV), plug-in hybrid electric vehicles (PHEV), or hybrid electric vehicles (HEV) where a low electrical conductivity coolant is required. 1.3 Coolants covered by this specification are not intended to circulate within a fuel cell stack in a fuel cell electric vehicle. 1.4 Coolant in this specification shall be used as supplied and need no further dilution by the user. 1.5 Coolants shall provide protection against corrosion, freezing, and overheating. 1.6 Coolants may circulate within the vehicle battery, or other vehicle components or may circulate through a cooling plate heat exchanger used to manage heat loads from batteries and other electrical components. Coolants shall not be used in direct immersion applications where there is a risk of contact with electrified components or circuits. 1.7 Coolants manage heat loads within the vehicle, prevent thermal runaway, and may serve to either cool or heat the batteries or electrical components. 1.8 Coolants shall be fully compatible with all system components in which they are in contact, including metals, polymers, and elastomers. 1.9 Coolants shall not be mixed or contaminated by a different coolant type. 1.10 Coolants may be used in non-vehicle applications. The requirements for non-vehicle applications are not addressed by this standard. 1.11 Coolants are not intended to be used in internal combustion engines. 1.12 Units—The values stated in SI units are to be regarded as standard. 1.13 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.14 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords battery electric vehicles (BEV); electric vehicle coolant; fuel cell electric vehicles (FCEV); hybrid electric vehicle (HEV); low electrical conductivity; plug-in hybrid electric vehicles (PHEV); ICS Code ICS Number Code 43.120 (Electric road vehicles) DOI: 10.1520/D8566-24 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|