|
FORMAT
BOOKS
PACKAGES
EDITION
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D8564 2024ASTM D8564-24Active Standard: Standard Test Method for Determination of Phenolic Antioxidants and Fuel System Icing Inhibitors in Aviation Turbine FuelsASTM D8564Scope 1.1 This test method covers the determination, in the interim precision ranges, of hindered phenolic antioxidants from approximately 1 mg/L to 50 mg/L and fuel system icing inhibitors from approximately 450 mg/L to 4500 mg/L in aviation turbine fuels by solid phase extraction (SPE) with gas chromatography-mass spectrometry detection (SPE-GC/MS). 1.1.1 Higher concentrations can be determined, but the interim precision of the test method has not been determined. 1.2 This test method is applicable to aviation turbine fuels that meet several international aviation turbine fuel specifications including, but not limited to, petroleum based, such as specified in Specification D1655, and synthetic aviation turbine fuels (SAF), such as specified in Specification D7566, and a blend of such fuels. 1.3 The test method does not purport to identify all of the individual antioxidants and fuel system icing inhibitors. The interim precision estimates have been determined in accordance with Practice D6300 for the following: 1.3.1 Phenolic Antioxidants—2,6-di-tert-butyltert-butylphenol; 2,4,6-tri-tert-butylphenol; 2,6-di-tert-butyl-4-methyl phenol; 4-sec-butyl-2,6-di-tert-butylphenol; 2-tert-butyl-4,6-dimethylphenol; 2-tert-butylphenol; 4-tert-butyl-2-methylphenol; and 1.3.2 Fuel System Icing Inhibitors—Diethylene glycol monomethyl ether (DiGME) and ethylene glycol monomethyl ether (EGM) (2-methoxyethanol). 1.3.3 Not all of the above antioxidants and/or fuel system icing inhibitors may be listed in all aviation turbine fuel specifications. User should consult the pertinent specification(s) for testing requirements. 1.4 Appendix X1 presents information on the data such as accuracy recovery studies and application to several types of aviation turbine fuels. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords antioxidants; aviation fuel; aviation turbine fuel; fuel system icing inhibitors; gas chromatography; gas chromatography/mass spectrometry; GC/MS; icing inhibitors; internal standard; phenols; solid phase extraction; SPE; ICS Code ICS Number Code 75.160.20 (Liquid fuels) DOI: 10.1520/D8564-24 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|