|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D8505/D8505M 2023ASTM D8505/D8505M-23Active Standard: Standard Specification for Basalt and Glass Fiber Reinforced Polymer (FRP) Bars for Concrete ReinforcementASTM D8505/D8505MScope 1.1 This specification covers basalt and glass fiber reinforced polymer (BFRP and GFRP, respectively) bars, provided in straight (longitudinal) cut lengths, of solid round cross-section, and having a surface enhancement for internal concrete reinforcement applications. Bars covered by this specification shall meet the requirements for geometric, material, mechanical, and physical properties as described herein. 1.2 Subsection 1.6 defines the type of FRP bars that are out of the scope of this specification. 1.3 Bars produced according to this standard are qualified using the test methods and must meet the requirements given in Table 1. Quality control and certification of production lots of bars are completed using the test methods and must meet the requirements given in Table 2. 1.4 The standard sizes and dimensions of FRP bars and their number designations are given in Table 3. 1.5 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables) shall not be considered as requirements of the specification. 1.6 The following FRP bar materials are not covered by this specification: 1.6.1 Bars made of more than one load-bearing fiber types or different grade fibers (that is, hybrid FRP). 1.6.2 Bars made from fibers other than glass or basalt. 1.6.3 Bars having no external surface enhancement (that is, plain or smooth bars, or dowels). 1.6.4 Bars with geometries other than solid, round cross sections. 1.6.5 Pre-manufactured grids and gratings made with FRP materials. 1.6.6 Bent bars (that is, bars that are not made of straight, continuous lengths). Note 1: Bent bars may include stirrups and hoops. Refer Specification D7957/D7957M for GFRP bent bar specifications. 1.7 This specification is applicable for either SI (as Specification D8505M) or US units (as Specification D8505). 1.8 The values stated in either SI units or US units are to be regarded as standard. Within the text, the US units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords bar; concrete reinforcement; Fiber Reinforced Polymer; FRP; non-metallic; rebar; reinforced concrete; ICS Code ICS Number Code 91.100.50 (Binders. Sealing materials) DOI: 10.1520/D8505_D8505M-23 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|