FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D7663 2024ASTM D7663-12-Reapproved2024Active Standard: Standard Practice for Active Soil Gas Sampling in the Vadose Zone for Vapor Intrusion EvaluationsASTM D7663Scope 1.1 Purpose—This practice covers standardized techniques for actively collecting soil gas samples from the vadose zone beneath or near dwellings and other buildings. 1.2 Objectives—Objectives guiding the development of this practice are: (1) to synthesize and put in writing good commercial and customary practice for active soil gas sampling, (2) to provide an industry standard for soil gas sampling performed in support of vapor intrusion evaluations that is practical and reasonable. 1.3 This practice allows a variety of techniques to be used for collecting soil gas samples because different techniques may offer certain advantages for specific applications. Three techniques are presented: sampling at discrete depths, sampling over a small screened interval, and sampling using permanent vapor monitoring wells. 1.4 Some of the recommendations require knowledge of pressure differential and tracer gas concentration measurements. 1.5 The values stated in SI units shall be regarded as standard. Other units are shown for information only. 1.6 This practice does not address requirements of any local, regional, state, provincial, or national regulations or guidance, or both, with respect to soil gas sampling. Users are cautioned that local, regional, state, provincial, or national guidance may impose specific requirements that differ from those of this practice. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM practice is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project's many unique aspects. The word “Standard” in the title means only that the document has been approved through the ASTM consensus process. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords sample measurement; soil gas; vadose zone; vapor intrusion; volatile organic compounds; ICS Code ICS Number Code 75.060 (Natural gas) DOI: 10.1520/D7663-12R24 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|