|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D7305 2013ASTM D7305 - 08a(2013)Standard Test Method for Reflection Density of Printed MatterActive Standard ASTM D7305 | Developed by Subcommittee: D01.56 Book of Standards Volume: 06.02 ASTM D7305Significance and Use 6.1 One of the key properties for printing in the lab or on production equipment is the intensity of the color, color balance and uniformity. This test can be used to ensure that the proper amount of ink is transferred to the substrate by obtaining a target density value, in addition to determining whether the print is uniform by measuring the reflection density over a wide print area. This then allows the use of the print for controlled testing of other appearance properties, such as gloss and color, and performance properties, such as resistance to abrasion and chemicals. 6.2 This test can be used to help achieve consistent color reproduction of printed color on flat surfaces. 6.3 Transfer of density readings from one set of inks to another, or from one substrate to another, carries a high risk of producing a color or tone shift. It is not in the scope of this test method to use density readings as digital proof of target points for printing process control. 1. Scope 1.1 This test method describes a procedure for measuring reflection density of printed matter using a reflection densitometer or spectrodensitometer. 1.2 This test method is intended primarily for process colors (yellow, magenta and cyan) and black. With appropriate instrumentation, it may also be used for other colors. 1.3 This test method applies to prints made by any printing process on a flat surface, with reflection density values ranging from just above zero, on the unprinted substrate, through to around 2.5 for very dense prints. 1.4 This test method can be used for prints on paper, film or board but not for those on metal or foil. It can be conducted in the pressroom or laboratory. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards E284 Terminology of Appearance E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method ANSI Standards PH2.18 Spectral Conditions for the Measurement of Optical DensityOther Standard DIN16536-2:1986 Testing of prints and printing inks in graphic technology -- Colour density measurements on on-press or off-press printsKeywords process color; reflection densitometer; reflection density; spectrodensitometer; ICS Number Code 37.100.01 DOI: 10.1520/D7305 ASTM International is a member of CrossRef. ASTM D7305This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|