|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D7127 2013ASTM D7127 - 13Standard Test Method for Measurement of Surface Roughness of Abrasive Blast Cleaned Metal Surfaces Using a Portable Stylus InstrumentActive Standard ASTM D7127 | Developed by Subcommittee: D01.46 Book of Standards Volume: 06.02 ASTM D7127Significance and Use 5.1 This method may be useful in assuring conformance of a prepared surface to profile requirements specified by the manufacturer of a protective coating. 5.2 This method includes determination of the peak density (number of profile peaks in a specified distance). Some workers in the field believe that optimizing peak height and peak density can improve coating adhesion. 5.3 This method allows specifiers to objectively define surface texture after abrasive blast cleaning rather than using subjective terms such as angular pattern or dense and uniform pattern. 5.4 Because implicit and explicit definitions of roughness may differ substantially, numerical characterizations of profile cannot be compared directly across different methods. 1. Scope 1.1 This test method describes a shop or field procedure for determination of roughness characteristics of surfaces prepared for painting by abrasive blasting. The procedure uses a portable skidded or non-skidded stylus profile tracing instrument. The measured characteristics are: Rt and Rpc . Additional measures of profile height ( Rmax and/or Rz ) may also be obtained as agreed upon by purchaser and seller. (The digitally-determined profile parameters Rt , Rmax , Ry and Rzlmax are extremely similar in definition.) 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 In general, this method should be limited to the measurement of surface roughness where Rt is in the range 10 to 150 ?m (0.4 to 6 mil) and where the Peak Count, Rpc is less than 180 peaks/cm (450 peaks/in.). 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASME Standard ASMEB46.1-2002 Surface Texture, Surface Roughness Waviness and Lay Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990.ISO Standards ISO4287:1997 Geometrical Product Specifications (GPS)--Surface Texture: Profile Method--Terms, Definitions, and Surface Parameters Available from International Organization for Standardization (ISO), 1 rue de Varemb, Case postale 56, CH-1211, Geneva 20, Switzerland.Keywords abrasive; abrasive blast cleaning; anchor pattern; peak count; surface profile; surface roughness; ICS Code ICS Number Code 25.220.10 (Surface preparation) DOI: 10.1520/D7127-13 ASTM International is a member of CrossRef. ASTM D7127The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|