|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D6815 2022ASTM D6815-22Historical Standard: Standard Specification for Evaluation of Duration of Load and Creep Effects of Wood and Wood-Based ProductsASTM D6815Scope 1.1 This specification provides a procedure for testing and evaluating duration of load and creep effects of wood and wood-based materials relative to an accepted duration of load adjustment model. This specification was created for products that are currently covered by a consensus standard (for example, lumber, structural composite lumber, and structural-use panels). This procedure is intended to demonstrate the engineering equivalence to the duration of load and creep effects of visually graded lumber as specified in Practice D245 for a product under evaluation used in dry service conditions. This procedure is not intended to evaluate the performance of products under impact loading. Quantification of specific duration of load or creep factors is beyond the scope of this specification. For further guidance regarding the applicability of this specification refer to X1.1 in the Commentary. 1.2 Use of the procedure in this specification to determine equivalence to the Practice D245 duration of load relationship is limited to solid wood and wood-based products whose long term load behavior is similar to that of solid wood. Equivalence demonstrated in this specification is dependent upon evaluation of a product's 90-day (minimum) creep-rupture performance. In this evaluation, three criteria must be satisfied: (1) adequate strength over a 90-day period, (2) decreasing creep rate, and (3) limited fractional deflection. A summary of the development of these criteria and the underlying assumptions behind them is provided in the Commentary in Appendix X1 and Appendix X2. 1.3 Long term degradation phenomena not described by a creep-rupture model are not addressed in this specification (see Commentary X1.2.4). 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords creep rate; creep-rupture; duration of load; fractional deflection; lumber; structural composite lumber; structural-use panels; ICS Code ICS Number Code 79.080 (Semi-manufactures of timber) DOI: 10.1520/D6815-22 The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|