1. Scope

1.1 This test method covers the guidelines, requirements and procedures for evaluating the ability of Rolled Erosion Control Products (RECPs) to protect earthen channels from stormwater-induced erosion. Critical elements of this protection are the ability of the RECP to:

1.1.1 Neutralize and absorb the hydraulic force of stormwater, thereby reducing soil particle loosening through 'scour' mechanisms;

1.1.2 Slow runoff and encourage sedimentation, thereby reducing soil particle transport downstream;

1.1.3 Absorb shear forces of overland flow;

1.1.4 Trap soil particles beneath; and

1.1.5 Promote the establishment of vegetation.

1.2 This test method utilizes full-scale testing procedures, rather than reduced-scale (bench-scale) simulation, and is patterned after conditions typically found on construction sites prior to and after revegetation work. Further, procedures for evaluation of baseline conditions are provided. Thus, test preparation, test execution, data collection, data analysis and reporting procedures herein are intended to be suitable for testing of bare soil, unvegetated RECP, vegetated soil and vegetated RECP conditions.

1.3 This test method provides a comparative evaluation of an unvegetated RECP to baseline bare soil conditions and a vegetated RECP to a baseline, vegetated condition under controlled and documented conditions.

1.4 The values stated in SI units are to be regarded as standard. The inch-pound units given in parentheses are provided for information purposes only.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Also, the user must comply with prevalent regulatory codes, such as OSHA (Occupational Health and Safety Administration) guidelines, while using the test method.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

C136 Test Method for Sieve Analysis of Fine and Coarse Aggregates

D422 Test Method for Particle-Size Analysis of Soils

D698 Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12 400 ft-lbf/ft3 (600 kN-m/m3))

D1556 Test Method for Density and Unit Weight of Soil in Place by Sand-Cone Method

D2922 Test Methods for Density of Soil and Soil-Aggregate in Place by Nuclear Methods (Shallow Depth)

D4318 Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils

D4595 Test Method for Tensile Properties of Geotextiles by the Wide-Width Strip Method

D6475 Test Method for Measuring Mass Per Unit Area of Erosion Control Blankets

D6525 Test Method for Measuring Nominal Thickness of Permanent Rolled Erosion Control Products

D6526 Test Method for Analysis of Toluene by Capillary Column Gas Chromatography

D6566 Test Method for Measuring Mass per Unit Area of Turf Reinforcement Mats

D6567 Test Method for Measuring the Light Penetration of a Turf Reinforcement Mat (TRM)

D6818 Test Method for Ultimate Tensile Properties of Turf Reinforcement Mats

Keywords

channel lining; ECB; erosion control; erosion control blanket; RECP; rolled erosion control product; scour; sediment; soil loss; TRM; turf reinforcement mat; Calibration--water analysis instrumentation; Channel lining; ECBs (erosion control blankets); Erosion control materials/applications; Full-scale testing; Installation--ground water/subsurface devices/applications; Performance--geosynthetics; Rolled erosion control product; Runoff; Scour protection; Sediment; Simulation testing; Soil loss; Stormwater-induced erosion; Water delivery systems/applications

ICS Code

ICS Number Code 13.080.01 (Soil quality in general)

DOI: 10.1520/D6460-07

ASTM International is a member of CrossRef.