FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D6253 2010ASTM D6253 - 10Standard Practice for Treatment and/or Marking of Wood Packaging MaterialsActive Standard ASTM D6253 | Developed by Subcommittee: D10.12 Book of Standards Volume: 15.10 ASTM D6253Significance and Use This practice establishes the criteria to treat, or mark, or both WPM with permanent identification for the phytosanitary treatment, or intended service cycle, or both, repair, specification used, and other designated characteristics. The marking of the WPM shall be performed after ensuring the material complies with the applicable specification. 1. Scope 1.1 This practice covers the development of recommended treatment, or marking practices, or both, for wood packaging materials (WPM) and aids in identifying WPM as to phytosanitary treatment, intended service cycles, repair, the specific specification used to manufacture or recycle, and other user designated characteristics. 1.2 This practice identifies WPM treated, or marked, or both in accordance with industry, government, or international recognized standards. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards D996 Terminology of Packaging and Distribution Environments D6039/D6039M Specification for Open and Covered Wood Crates D6251/D6251M Specification for Wood-Cleated Panelboard Shipping Boxes D6254/D6254M Specification for Wirebound Pallet-Type Wood Boxes D6255/D6255M Specification for Steel or Aluminum Slotted Angle Crates D6256/D6256M Specification for Wood-Cleated Shipping Boxes with Skidded, Load-Bearing Bases D6573/D6573M Specification for General Purpose Wirebound Shipping Boxes MHIA Standard MHIAMH12005 Pallets, Slip Sheets, and Other Bases for Unit Loads Available from Material Handling Industry of America (MHIA), 8720 Red Oak Blvd., Suite 201, Charlotte, NC 28217-3992, http://www.mhia.org.AWPA Standards P9-03, Standards for Solvents and Formulations for Organic Preservative SystemsNFPA Standard NFPA704, Standard System for Identification of Hazards of Materials for Emergency Response Available from National Fire Protection Association (NFPA), 1 Batterymarch Park, Quincy, MA 02269-9101.International Standard InternationalStandar Regulation of Wood Packaging Material in International Trade Available from the International Plant Protection Convetion, www.ippc.int.Keywords containers; crates; marking; pallets; phytosanitary treatment; wood packaging materials; Marking of pallets; Pallets; Uniform marking practices; ICS Code ICS Number Code 55.180.99 (Other standards related to freight distribution of goods) DOI: 10.1520/D6253-10 ASTM International is a member of CrossRef. ASTM D6253The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|