1. Scope

1.1 This guide is intended as an information aid to painting inspectors in carrying out the task efficiently. It includes the key elements of surface preparation, coatings application, and final approval for both field and shop work. The items should be selected that are pertinent to a particular job.

Note 1For additional helpful information, refer to the following documents:

Manual of Concrete Practice ACI 515R American Concrete Institute

Manual of Coating Work for Light Water Nuclear Power Plant Primary Containment and Other Safety Related Facilities

C 811 Practice for Surface Preparation of Concrete for Application of Chemical-Resistant Resin Monolithic Surfacings

SSPC-PA Guide 3 - A Guide to Safety in Paint Application

Steel Structures Painting Manual Vol. 1- Good Painting Practices

Steel Structures Painting Manual Vol. 2 - Systems and Specifications

Manufacturers Specifications and Instructions (made available to the inspector for reference to special requirements for proper application)

Material Safety Data Sheets (needed to insure that personnel take necessary precautions in handling hazardous materials) Available from Materials manufacturer.

1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of whomever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

C811 Practice for Surface Preparation of Concrete for Application of Chemical-Resistant Resin Monolithic Surfacings

D1212 Test Methods for Measurement of Wet Film Thickness of Organic Coatings

D1475 Test Method For Density of Liquid Coatings, Inks, and Related Products

D3359 Test Methods for Measuring Adhesion by Tape Test

D4138 Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-Sectioning Means

D4212 Test Method for Viscosity by Dip-Type Viscosity Cups

D4258 Practice for Surface Cleaning Concrete for Coating

D4259 Practice for Abrading Concrete

D4260 Practice for Liquid and Gelled Acid Etching of Concrete

D4262 Test Method for pH of Chemically Cleaned or Etched Concrete Surfaces

D4263 Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method

D4285 Test Method for Indicating Oil or Water in Compressed Air

D4414 Practice for Measurement of Wet Film Thickness by Notch Gages

D4787 Practice for Continuity Verification of Liquid or Sheet Linings Applied to Concrete Substrates

D5064 Practice for Conducting a Patch Test to Assess Coating Compatibility

D6132 Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Gage

D6677 Test Method for Evaluating Adhesion by Knife

D7234 Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers

E1907 Guide to Methods of Evaluating Moisture Conditions of Concrete Floors to Receive Resilient Floor Coverings

F1869 Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride

F2170 Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes

International Concrete Repair Institute

Keywords

abrasive blasting; acid treatment (concrete); adhesion; chemical cleaning; coatings; concrete; detergents; inspection; laitance; masonry; moisture; Inspection--coating applications; Moisture analysis--paints/related coatings/materials; Substrates--coating applications; Acid treatment (concrete); Chemical cleaning; Concrete; Inspection personnel/inspectors; Laitance; Abrasive blasting; Masonry substrates; Paint inspectors;

ICS Code

ICS Number Code 87.020 (Paint coating processes); 91.060.10 (Walls. Partitions. Facades)

DOI: 10.1520/D6237-03

ASTM International is a member of CrossRef.