FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D3517 2011ASTM D3517 - 11Standard Specification for 'Fiberglass' (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure PipeActive Standard ASTM D3517 | Developed by Subcommittee: D20.23 Book of Standards Volume: 08.03 ASTM D3517Abstract This specification covers machine-made fiberglass (glass-fiber-reinforced thermosetting-resin or glass-fiber-reinforced polymer mortar) pressure pipe intended for use in water conveyance systems. It is suited primarily for pipes to be installed in buried applications, although it may be used to the extent applicable for other installations such as, but not limited to, jacking, tunnel lining, and slip lining rehabilitation of existing pipelines. The materials shall include the following: structural wall composition which shall consist of thermosetting resin, glass fiber reinforcement, and, if used, aggregate filler; a thermosetting polyester or epoxy resin with or without filler; E-type glass reinforcement; siliceous sand aggregates; liner and surface layers; unrestrained or restrained joints; and elastomeric gaskets. Pipe shall be supplied in the nominal diameters, lengths, wall thickness, squareness of pipe ends, and soundness. Test specimen shall be subjected to longitudinal loads or circumferential bending to test for its long-term hydrostatic design pressure. The pipe shall conform to the stiffness, hoop-tensile strength, joint tightness, beam strength, longitudinal compressive strength, and longitudinal tensile strength requirements. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. 1. Scope 1.1 This specification covers machine-made fiberglass pipe, 8 in. (200 mm) through 156 in. (4000 mm), intended for use in water conveyance systems which operate at internal gage pressures of 450 psi (3103 kPa) or less. Both glass-fiber-reinforced thermosetting-resin pipe (RTRP) and glass-fiber-reinforced polymer mortar pipe (RPMP) are fiberglass pipes. The standard is suited primarily for pipes to be installed in buried applications, although it may be used to the extent applicable for other installations such as, but not limited to, jacking, tunnel lining and slip-lining rehabilitation of existing pipelines. Note 1For the purposes of this standard, polymer does not include natural polymers. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only. Note 2There is no known ISO equivalent to this standard. 1.3 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards C33 Specification for Concrete Aggregates D638 Test Method for Tensile Properties of Plastics D695 Test Method for Compressive Properties of Rigid Plastics D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials D883 Terminology Relating to Plastics D1600 Terminology for Abbreviated Terms Relating to Plastics D2290 Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading D2584 Test Method for Ignition Loss of Cured Reinforced Resins D2992 Practice for Obtaining Hydrostatic or Pressure Design Basis for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings D3567 Practice for Determining Dimensions of Fiberglass (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings D3892 Practice for Packaging/Packing of Plastics D4161 Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals F412 Terminology Relating to Plastic Piping Systems F477 Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe NSF Standard Standard No. 61 Drinking Water System Components Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140, http://www.nsf.org.ISO Standard ISO 1172 Textile Glass Reinforced Plastics--Determination of Loss on Ignition Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.Keywords fiberglass pipe; hydrostatic design basis; pressure pipe ; RPMP; RTRP: Fiberglass pipe--specifications; Hydrostatic testing; Reinforced thermosetting-resin pipe (RTRP)--specifications; RPMP (reinforced polymer mortar pipe); Water supply/distribution systems--specifications; ICS Code ICS Number Code 23.040.20 (Plastic pipes) DOI: 10.1520/D3517-11 ASTM International is a member of CrossRef. ASTM D3517The following editions for this book are also available...
This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|