|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D3350 2021ASTM D3350-21Historical Standard: Standard Specification for Polyethylene Plastics Pipe and Fittings MaterialsASTM D3350Scope 1.1 This specification covers the identification of polyethylene plastic pipe and fittings materials in accordance with a cell classification system. It is not the function of this specification to provide specific engineering data for design purposes, to specify manufacturing tolerances, or to determine suitability for use for a specific application. 1.1.1 Some plastic pipe and fitting PE compounds classified by this standard are sold as a base material and then combined with other material(s) (for example, color or additive concentrate) by the pipe or fitting manufacturer into a final classified compound either prior to or during production of the final article. This standard, excluding the requirements of Table 1, properties 5 and 6, and 6.1.1, can be used for property verification of the incoming base material(s) in accordance with 8.1. 1.1.2 In the case of PE compounds sold as the compound classified by the standard, see 8.1 regarding property verification of the incoming classified compound. 1.1.3 Compounds with a cell classification value other than ‘0’ for the Hydrostatic Strength Classification (property 6) rely on a defined formulation. The composition of the defined formulation can be obtained from the owner of the formulation. Note 1: Deviations from the defined formulation may affect the Hydrostatic Strength Classification. 1.2 Polyethylene plastic materials, being thermoplastic, are reprocessable and recyclable (Note 3). This specification allows for the use of those polyethylene materials, provided that all specific requirements of this specification are met. Note 2: The notes in this specification are for information only and shall not be considered part of this specification. Note 3: See Guide D5033 for information and definitions related to recycled plastics. 1.3 The values stated in SI units are to be regarded as standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 4: There is no known ISO equivalent to this standard. 1.5 For information regarding molding and extrusion materials see Specification D4976. For information regarding wire and cable materials see Specification D1248. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords cell classification system; pipe and fittings material; polyethylene; recycled; ICS Code ICS Number Code 23.040.20 (Plastic pipes) DOI: 10.1520/D3350-21 The following editions for this book are also available...
This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|