FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D1418 2010ASTM D1418 - 10aStandard Practice for Rubber and Rubber Latices-NomenclatureActive Standard ASTM D1418 | Developed by Subcommittee: D11.08 Book of Standards Volume: 09.01
Translated Standard: Russian ASTM D1418Abstract This practice covers a system of general classification or nomenclature for rubber and rubber latices. Rubbers in both dry and latex form shall be coded from the chemical composition of the polymer chain using the following classes: M, N, O, R, Q, T, U, and Z. The M shall be classified as follows: ACM, AEM, ANM, BIMSM, CM, CFM, CSM, EOM, EPDM, EPM, EVM, FEPM, FFKM, FKM, Type 1, Type 2, Type 3, Type 4, Type 5, and IM. The O class shall be classified as follows: CO, ECO, GECO, and GPO. The R class shall be classified as follows: ABR, BIIR, BR, CIIR, CR,ENR, ENRG, HNBR, IIR, IR, NBR, NIR, NR, NRG, PBR, PSBR, SBR, SIR, XBR, XSBR, and XNBR, where the parenthetical letter S or E shall be used to indicate whether the rubber or latex was prepared by solution or emulsion polymerization and the prefix X shall be used if the rubber have substitute carboxylic acid groups. The Q shall be classified as follows: FMQ, FVMQ, PMQ, PVMQ, MQ, and VMQ. The U class shall be classified as AFMU, AU, And EU. The T class shall be classified as OT and EOT. The Z class shall be classified as FZ and PZ. Mixtures of rubbers are identified by using the class designations for the types of rubbers in the mixture, with the major component listed first if the composition is known and in alphabetical order if the rubbers are present in equal amounts. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. 1. Scope 1.1 This practice covers a system of general classification for the basic rubbers both in dry and latex forms determined from the chemical composition of the polymer chain. 1.2 The purpose of this practice is to provide a standardization of terms for use in industry, commerce, and government and is not intended to conflict with but rather to act as a supplement to existing trade names and trademarks. 1.3 In technical papers or presentations the name of the polymer should be used if possible. The symbols can follow the chemical name for use in later references. Note 1For terms related to thermoplastic elastomers, see Practice D5538 .
ASTM Standards D5538 Practice for Thermoplastic Elastomers--Terminology and Abbreviations Keywords acronyms for latices; acronyms for rubber; nomenclature; Classification (standards)--rubber; FKM; Natural rubber (NR) latex; Nomenclature; Rubber; Terminology--rubber compounds/materials ; ICS Code ICS Number Code 83.060 (Rubber) DOI: 10.1520/D1418-10A ASTM International is a member of CrossRef. ASTM D1418The following editions for this book are also available...
This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|