FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D1275 2006ASTM D1275 - 06Standard Test Method for Corrosive Sulfur in Electrical Insulating OilsActive Standard ASTM D1275 | Developed by Subcommittee: D27.06 Book of Standards Volume: 10.03
Translated Standard: Russian ASTM D1275Significance and Use In most of their uses, insulating oils are continually in contact with metals that are subject to corrosion. The presence of corrosive sulfur compounds will result in deterioration of these metals. The extent of deterioration is dependent upon the quantity and type of corrosive agent and time and temperature factors. Detection of these undesirable impurities, even though not in terms of quantitative values, is a means for recognizing the hazard involved. 1. Scope 1.1 This test method describes the detection of corrosive sulfur compounds (both inorganic and organic) in electrical insulating oils of petroleum origin. 1.2 New and in-service mineral insulating oils may contain substances that cause corrosion under certain conditions of use. This test method is designed to detect the presence of, or the propensity to form, free (elemental) sulfur and corrosive sulfur compounds by subjecting copper to contact with oil under prescribed conditions. 1.3 Two methods (A and B) have been introduced where historically there has only been one. Method A is the one that has been in place since 1953. Method B is more rigorous and the preferred method. 1.4 The values stated in SI units are to be regarded as the standard. Inch-pound units are included for informational purposes. This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards D130 Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test Other Document ANSIB74.10 Grading of Abrasive Microgrits Available from American National Standards Institute, 25 W. 43rd St., 4th Floor, New York, NY 10036, USA.Keywords corrosion; fluid; insulating; mineral; oils; petroleum sulfur; ICS Code ICS Number Code 29.040.10 (Insulating oils) DOI: 10.1520/D1275-06 ASTM International is a member of CrossRef. ASTM D1275The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|