|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-C1314 2012ASTM C1314 - 12Standard Test Method for Compressive Strength of Masonry PrismsActive Standard ASTM C1314 | Developed by Subcommittee: C15.04 Book of Standards Volume: 04.05 ASTM C1314Significance and Use 4.1 This test method provides a means of verifying that masonry materials used in construction result in masonry that meets the specified compressive strength. 4.2 This test method provides a means of evaluating compressive strength characteristics of in-place masonry construction through testing of prisms obtained from that construction when sampled in accordance with Practice C1532 . Decisions made in preparing such field-removed prisms for testing, determining the net area, and interpreting the results of compression tests require professional judgment. 4.3 If this test method is used as a guideline for performing research to determine the effects of various prism construction or test parameters on the compressive strength of masonry, deviations from this test method shall be reported. Such research prisms shall not be used to verify compliance with a specified compressive strength of masonry.
Note 1 The testing laboratory performing this test method should be evaluated in accordance with Practice C1093
.
4.3.1 Appendix X2 includes guidance information for the researcher on aspects of materials, construction, and analysis. 1. Scope 1.1 This test method covers procedures for masonry prism construction and testing, and procedures for determining the compressive strength of masonry, f mt , used to determine compliance with the specified compressive strength of masonry, f?? m . When this test method is used for research purposes, the construction and test procedures within serve as a guideline and provide control parameters. 1.2 This test method also covers procedures for determining the compressive strength of prisms obtained from field-removed masonry specimens. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards C67 Test Methods for Sampling and Testing Brick and Structural Clay Tile C136 Test Method for Sieve Analysis of Fine and Coarse Aggregates C140 Test Methods for Sampling and Testing Concrete Masonry Units and Related Units C143/C143M Test Method for Slump of Hydraulic-Cement Concrete C144 Specification for Aggregate for Masonry Mortar C270 Specification for Mortar for Unit Masonry C476 Specification for Grout for Masonry C780 Test Method for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry C1019 Test Method for Sampling and Testing Grout C1093 Practice for Accreditation of Testing Agencies for Masonry C1532 Practice for Selection, Removal, and Shipment of Manufactured Masonry Units and Masonry Specimens from Existing Construction C1552 Practice for Capping Concrete Masonry Units, Related Units and Masonry Prisms for Compression Testing C1587 Practice for Preparation of Field Removed Manufactured Masonry Units and Masonry Specimens for Testing E105 Practice for Probability Sampling of Materials E111 Test Method for Youngs Modulus, Tangent Modulus, and Chord Modulus Keywords compressive strength of masonry ( f mt ); masonry prism; masonry prism strength; masonry specimen; specified compressive strength of masonry ( f ???? m ); ICS Code ICS Number Code 19.060 (Mechanical testing); 91.080.30 (Masonry) DOI: 10.1520/C1314-12 ASTM International is a member of CrossRef. ASTM C1314The following editions for this book are also available...
This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|