Significance and Use

This guide is a compilation of standards intended to provide assistance in selecting appropriate nondestructive examination for advanced ceramics, and in turn, to provide guidance for performing the examination, as well as ensuring the proper performance of the equipment.

1. Scope

1.1 This guide identifies and describes standard procedures and methods for nondestructive testing of advanced ceramics using radiology, ultrasonics, liquid penetrants, and acoustic emission.

1.2 This guide identifies existing standards for nondestructive testing that have been determined to be (or have been modified to be) applicable to the examination of advanced ceramics. These standards have been generated by, and are under the jurisdiction of, ASTM Committee E07 on Nondestructive Testing. Selection and application of these standards to be followed must be governed by experience and the specific requirements in each individual case, together with agreement between producer and user.

1.3 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

E94 Guide for Radiographic Examination

E114 Practice for Ultrasonic Pulse-Echo Straight-Beam Contact Testing

E165 Practice for Liquid Penetrant Examination for General Industry

E317 Practice for Evaluating Performance Characteristics of Ultrasonic Pulse-Echo Testing Instruments and Systems without the Use of Electronic Measurement Instruments

E494 Practice for Measuring Ultrasonic Velocity in Materials

E569 Practice for Acoustic Emission Monitoring of Structures During Controlled Stimulation

E587 Practice for Ultrasonic Angle-Beam Contact Testing

E650 Guide for Mounting Piezoelectric Acoustic Emission Sensors

E664 Practice for the Measurement of the Apparent Attenuation of Longitudinal Ultrasonic Waves by Immersion Method

E750 Practice for Characterizing Acoustic Emission Instrumentation

E797 Practice for Measuring Thickness by Manual Ultrasonic Pulse-Echo Contact Method

E976 Guide for Determining the Reproducibility of Acoustic Emission Sensor Response

E999 Guide for Controlling the Quality of Industrial Radiographic Film Processing

E1000 Guide for Radioscopy

E1065 Guide for Evaluating Characteristics of Ultrasonic Search Units

E1079 Practice for Calibration of Transmission Densitometers

E1106 Test Method for Primary Calibration of Acoustic Emission Sensors

E1165 Test Method for Measurement of Focal Spots of Industrial X-Ray Tubes by Pinhole Imaging

E1208 Practice for Fluorescent Liquid Penetrant Testing Using the Lipophilic Post-Emulsification Process

E1209 Practice for Fluorescent Liquid Penetrant Testing Using the Water-Washable Process

E1210 Practice for Fluorescent Liquid Penetrant Testing Using the Hydrophilic Post-Emulsification Process

E1219 Practice for Fluorescent Liquid Penetrant Testing Using the Solvent-Removable Process

E1220 Practice for Visible Penetrant Testing Using Solvent-Removable Process

E1254 Guide for Storage of Radiographs and Unexposed Industrial Radiographic Films

E1255 Practice for Radioscopy

E1316 Terminology for Nondestructive Examinations

E1324 Guide for Measuring Some Electronic Characteristics of Ultrasonic Testing Instruments

E1390 Specification for Illuminators Used for Viewing Industrial Radiographs

E1411 Practice for Qualification of Radioscopic Systems

E1441 Guide for Computed Tomography (CT) Imaging

E1453 Guide for Storage of Magnetic Tape Media that Contains Analog or Digital Radioscopic Data

E1570 Practice for Computed Tomographic (CT) Examination

E1647 Practice for Determining Contrast Sensitivity in Radiology

E1672 Guide for Computed Tomography (CT) System Selection

E1695 Test Method for Measurement of Computed Tomography (CT) System Performance

E1781 Practice for Secondary Calibration of Acoustic Emission Sensors

E1817 Practice for Controlling Quality of Radiological Examination by Using Representative Quality Indicators (RQIs)

Keywords

acoustic emission; advanced ceramics; equipment calibration; flaw detection; liquid penetrants; measurement of properties; nondestructive testing; radiography; radiology; ultrasonics; Acoustic emission (AE) testing; Advanced ceramics; Attenuation; Ultrasonic testing--advanced ceramics; Calibration--acoustic emission analysis instrumentation; Liquid penetration; Nondestructive evaluation (NDE); Radiographic examination; Radiological examination; Radioscopic examination; Surface analysis--ceramics;

ICS Code

ICS Number Code 81.060.99 (Other standards related to ceramics)

DOI: 10.1520/C1175-99AR10

ASTM International is a member of CrossRef.

ASTM C1175