1. Scope

1.1 These test methods cover physical testing of quicklime and hydrated lime, and of limestone not otherwise covered in ASTM standards.

Note 1Quicklime and hydrated lime have a high affinity for moisture and carbon dioxide. Caution should be taken to protect both hydrated and quicklime during sampling, storage, and testing (see Practice C 50).

1.2 The values stated in SI units are to be regarded as the standard.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

C28/C28M Specification for Gypsum Plasters

C50 Practice for Sampling, Sample Preparation, Packaging, and Marking of Lime and Limestone Products

C51 Terminology Relating to Lime and Limestone (as used by the Industry)

C91 Specification for Masonry Cement

C109/C109M Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)

C136 Test Method for Sieve Analysis of Fine and Coarse Aggregates

C150 Specification for Portland Cement

C185 Test Method for Air Content of Hydraulic Cement Mortar

C188 Test Method for Density of Hydraulic Cement

C192/C192M Practice for Making and Curing Concrete Test Specimens in the Laboratory

C204 Test Methods for Fineness of Hydraulic Cement by Air-Permeability Apparatus

C207 Specification for Hydrated Lime for Masonry Purposes

C230/C230M Specification for Flow Table for Use in Tests of Hydraulic Cement

C231 Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method

C305 Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency

C430 Test Method for Fineness of Hydraulic Cement by the 45-m (No. 325) Sieve

C472 Test Methods for Physical Testing of Gypsum, Gypsum Plasters and Gypsum Concrete

C595 Specification for Blended Hydraulic Cements

C670 Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials

C702 Practice for Reducing Samples of Aggregate to Testing Size

C778 Specification for Sand

C1005 Specification for Reference Masses and Devices for Determining Mass and Volume for Use in the Physical Testing of Hydraulic Cements

C1107 Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink)

D75 Practice for Sampling Aggregates

E11 Specification for Woven Wire Test Sieve Cloth and Test Sieves

E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods

E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

Keywords

accepted reference value; accuracy; apparent density; bias; dry brightness; dry screening; fineness; interlaboratory study; lime putty; limestone grindability; particle size; precision; precision conditions; repeatability; reproducibility; slaking rate; standard deviation: Air entrainment; Autoclave expansion; Acidity, alkalinity, pH; Brightness; Change in length; Consistency; Dry brightness; Expansion--concrete materials/applications; Hydrated lime; Lime putty; Limestone; Optical materials/properties/tests; Plasticity index; Popping and pitting; Quicklime; Residue; Settlement; Sieve analysis--building materials; Slaking rate; Water retention

ICS Code

ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)

DOI: 10.1520/C0110-04

ASTM International is a member of CrossRef.