ASTM B124/B124M-08a
Historical Standard: ASTM B124/B124M-08a Standard Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes
SUPERSEDED (see Active link, below)
ASTM B124 / B124M
1. Scope
1.1 This specification establishes the requirements for copper and copper alloy rod, bar, and shapes intended for hot forging. The following coppers and copper alloys are involved:
|
Copper UNS Nos. |
Copper Alloy UNS Nos. |
| C11000 | C36500 |
| C14500 | C37000 |
| C14700 | C37700 |
| C46400 | |
| C48200 | |
| C48500 | |
| C61900 | |
| C62300 | |
| C63000 | |
| C63200 | |
| C64200 | |
| C64210 | |
| C65500 | |
| C67500 | |
| C67600 | |
| C69300 | |
| C70620 | |
| C71520 | |
| C77400 |
Note 1Additional information about forging practice and forgings produced from these alloys is given in Appendix X1 and in Specification B 283 .
1.2 Units The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
B249/B249M Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
B283 Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
E54 Test Methods for Chemical Analysis of Special Brasses and Bronzes
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys
E76 Test Methods for Chemical Analysis of Nickel-Copper Alloys
E121 Test Methods for Chemical Analysis of Copper-Tellurium Alloys
E478 Test Methods for Chemical Analysis of Copper Alloys
Keywords
bar; brass; brass forging shapes; brass forgings; bronze; bronze forging shapes; copper; copper alloy; copper alloy forgings; copper alloy forging bar; copper alloy forging rod; copper alloy forging shapes; copper forging bar; copper forging rod; copper forging shapes; copper forgings; copper nickel; copper nickel forging rod; copper nickel forgings; hot forging; hot forging stock; nickel silver; nickel silver forging shapes; nickel silver forgings; rod; shapes; UNS Alloy Nos. C27450; C35330; C36500; C37000; C37700; C46400; C48200; C48500; C48600; C49250; C49255; C49260; C49300; C49340; C49350; C49355; C49360; C61900; C62300; C63000; C63200; C64200; C64210; C65500; C67500; C67600; C69150; C69300; C70620; C71520; C77400; UNS Nos. C11000; C14500; C14700; C87700; C87710; ICS Number Code 4700
DOI: 10.1520/B0124_B0124M-08A
ASTM International is a member of CrossRef.
