1. Scope

1.1 This specification covers general procedures for specifying requirements in the procurement and delivery of flat-rolled electrical steels for magnetic applications. When an applicable individual specification does not exist, this specification enables the user to order a suitable material to be supplied under controlled conditions with respect to magnetic quality, sampling, testing, packaging, and so forth, by specifying certain requirements on the purchase order and citing this specification.

1.2 Individual specifications that are in conformity with this specification are Specifications A 677/A 677M, A 683/A 683M, A 726, A 840, and A 876.

For more information on procedures associated with this specification, refer to the following: Test Methods A 341/A 341M, A 343/A 343M, A 348/A 348M, A 596/A 596M, A 712, A 719/A 719M, A 720/A 720M, A 721/A 721M, A 773/A 773M, A 804/A 804M, A 889/A 889M, A 937/A 937M, A 971, and Practice A 664.

1.3 The following safety hazards caveat pertains only to the test methods portion, Section 13, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

A34/A34M Practice for Sampling and Procurement Testing of Magnetic Materials

A340 Terminology of Symbols and Definitions Relating to Magnetic Testing

A341/A341M Test Method for Direct Current Magnetic Properties of Materials Using D-C Permeameters and the Ballistic Test Methods

A343/A343M Test Method for Alternating-Current Magnetic Properties of Materials at Power Frequencies Using Wattmeter-Ammeter-Voltmeter Method and 25-cm Epstein Test Frame

A348/A348M Test Method for Alternating Current Magnetic Properties of Materials Using the Wattmeter-Ammeter-Voltmeter Method, 100 to 10a??000 Hz and 25-cm Epstein Frame

A596/A596M Test Method for Direct-Current Magnetic Properties of Materials Using the Ballistic Method and Ring Specimens

A664 Practice for Identification of Standard Electrical Steel Grades in ASTM Specifications

A677 Specification for Nonoriented Electrical Steel Fully Processed Types

A683 Specification for Nonoriented Electrical Steel, Semiprocessed Types

A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment

A712 Test Method for Electrical Resistivity of Soft Magnetic Alloys

A717/A717M Test Method for Surface Insulation Resistivity of Single-Strip Specimens

A719/A719M Test Method for Lamination Factor of Magnetic Materials

A720/A720M Test Method for Ductility of Nonoriented Electrical Steel

A721/A721M Test Method for Ductility of Oriented Electrical Steel

A726 Specification for Cold-Rolled Magnetic Lamination Quality Steel, Semiprocessed Types

A773/A773M Test Method for dc Magnetic Properties of Materials Using Ring and Permeameter Procedures with dc Electronic Hysteresigraphs

A804/A804M Test Methods for Alternating-Current Magnetic Properties of Materials at Power Frequencies Using Sheet-Type Test Specimens

A840 Specification for Fully Processed Magnetic Lamination Steel

A876 Specification for Flat-Rolled, Grain-Oriented, Silicon-Iron, Electrical Steel, Fully Processed Types

A889/A889M Test Method for Alternating-Current Magnetic Properties of Materials at Low Magnetic Flux Density Using the Voltmeter-Ammeter-Wattmeter-Varmeter Method and 25-cm Epstein Frame

A937/A937M Test Method for Determining Interlaminar Resistance of Insulating Coatings Using Two Adjacent Test Surfaces

A971/A971M Test Method for Measuring Edge Taper and Crown of Flat-Rolled Electrical Steel Coils

A976 Classification of Insulating Coatings for Electrical Steels by Composition, Relative Insulating Ability and Application

Keywords

electrical steel; fully processed; grain-oriented electrical steel; identification; magnetic lamination steel; nonoriented electrical steel; semiprocessed; Electrical insulating materials--specifications; Electrical steel--specifications; Flat-rolled electrical steel; Magnetic materials/applications--specifications; Procurement and delivery;

ICS Code

ICS Number Code 77.140.50 (Flat steel products and semi-products)

DOI: 10.1520/A0345-04

ASTM International is a member of CrossRef.