ASTM A325M-00
Historical Standard: ASTM A325M-00 Standard Specification for High-Strength Bolts for Structural Steel Joints [Metric]
SUPERSEDED (see Active link, below)
ASTM A325M
1. Scope
1.1 This specification covers requirements of various types of quenched and tempered steel bolts in nominal thread diameters M16 to M36 inclusive, commonly known as 'high-strength structural bolts,' intended for use in structural joints that are comparable to those made under the Specifications for Structural Joints Using ASTM A325 or A490 Bolts, issued by the Research Council on Structural Connections of the Engineering Foundation. Types of bolts covered in this specification are:
1.1.1 Type 1 -Bolts made of medium-carbon steel.
1.1.2 Type 2 -Bolts made from what is generally described as low-carbon martensite steel.
1.1.3 Type 3 -Bolts made of steel having atmospheric corrosion resistance and weathering characteristics comparable to that of the steel covered in Specifications A588/ A588M, A242/A242M, and A709/A709M. The atmospheric corrosion resistance of these steels is substantially better than that of carbon steel with or without copper addition (see 5.3). When properly exposed to the atmosphere, these steels can be used bare (uncoated) for many applications.
1.2 This specification provides that heavy hex structural bolts shall be furnished unless other dimensional requirements are stipulated in the purchase inquiry and order.
1.3 Unless otherwise specified, all nuts used on these bolts shall conform to the requirements of Specification A563M shall be heavy hex, and shall be of the class and surface finish for each type of bolt as follows:
Bolt Type and Finish Nut Class and Finish 1 and 2, plain (noncoated) 8S or 8S3, plain 1 and 2, zinc-coated 10S, zinc-coated 3, plain 8S3, plain1.4 Unless otherwise specified, all washers used on these bolts shall conform to the requirements of Specification F436M and shall be of a surface finish for each type of bolt as follows:
Bolt Type and Finish Washer Finish 1 and 2, plain (uncoated) plain (uncoated) 1 and 2, zinc-coated 3, plain weathering steel, plain1.5 Zinc-coated bolts and nuts shall be shipped in the same container.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASME Standards
B 18.24 Part Identifying Number (PIN) Code System Standard for B18 Fastener ProductsASTM Standards
A153/A153M Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware
A490M Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints (Metric)
A563M Specification for Carbon and Alloy Steel Nuts (Metric)
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
B695 Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
D3951 Practice for Commercial Packaging
F436M Specification for Hardened Steel Washers (Metric)
F606M Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets (Metric)
F788/F788M Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series
F959M Specification for Compressible-Washer-Type Direct Tension Indicators for Use With Structural Fasteners (Metric)
F1136M Specification for Zinc/Aluminum Corrosion Protective Coatings for Fasteners (Metric)
F1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
F1789 Terminology for F16 Mechanical Fasteners
G101 Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels
Keywords
alloy steel; bolts; carbon steel; metric; steel; structural; weathering steel;
ICS Code
ICS Number Code 21.060.10 (Bolts, screws, studs)
DOI: 10.1520/A0325M-00
ASTM International is a member of CrossRef.