Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?

PD IEC/TR 62368-2:2015 Audio/video, information and communication technology equipment - Explanatory information related to IEC 62368-1, 2015
- 30321633-VOR.pdf [Go to Page]
- FOREWORD
- Clause 0 Principles of this product safety standard
- Clause 1 Scope
- Clause 2 Normative references
- Clause 3 Terms, definitions and abbreviations
- Clause 4 General requirements
- Clause 5 Electrically-caused injury
- Clause 6 Electrically-caused fire
- Clause 7 Injury caused by hazardous substances
- Clause 8 Mechanically-caused injury
- Clause 9 Thermal burn injury
- Clause 10 Radiation
- Annex A(informative) Background information related to the use of SPDs
- Annex B (informative) Background information related to measurement of discharges – Determining the R-C discharge time constant for X- and Y-capacitors
- Annex C (informative) Background information related to resistance to candle flame ignition
- Bibliography
- Figures [Go to Page]
- Figure 1 – Conventional time/current zones of effects of a.c. currents (15 Hz to 100 Hz) on persons for a current path corresponding to left hand to feet (see IEC TS 60479-1:2005, Figure 20)
- Figure 2 – Conventional time/current zones of effects of d.c. currents on personsfor a longitudinal upward current path (see IEC TS 60479-1:2005, Figure 22)
- Figure 3 – Illustration that limits depend on both voltage and current
- Figure 4 – Illustration of transient voltages on paired conductor external circuits
- Figure 5 – Illustration of transient voltages on coaxial-cable external circuits
- Figure 6 – Basic and reinforced insulation in Table 15 of IEC 62368-1:2014 –Ratio reinforced to basic
- Figure 7 – Reinforced clearances according to Rule 1, Rule 2, and Table 15
- Figure 8 – Example illustrating accessible internal wiring
- Figure 9 – Waveform on insulation without surgesuppressors and no breakdown
- Figure 10 – Waveforms on insulation during breakdownwithout surge suppressors
- Figure 11 – Waveforms on insulation withsurge suppressors in operation
- Figure 12 – Waveform on short-circuitedsurge suppressor and insulation
- Figure 13 – Example for an ES2 source
- Figure 14 – Example for an ES3 source
- Figure 15 – Overview of protective conductors
- Figure 17 – Touch current from a floating circuit
- Figure 18 – Touch current from an earthed circuit
- Figure 19 – Summation of touch currents in a PABX
- Figure 20 – Possible safeguards against electrically-caused fire
- Figure 21 – Fire clause flow chart
- Figure 22 – Prevent ignition flow chart
- Figure 23 – Control fire spread summary
- Figure 24 – Control fire spread PS2
- Figure 25 – Control fire spread PS3
- Figure 26 – Fire cone application to large component
- Figure 27 – Flowchart demonstrating the hierarchy of hazard management
- Figure 28 – Model for chemical injury
- Figure 29 – Direction of forces to be applied
- Figure 30 – Model for a burn injury
- Figure 31 – Model for safeguards against thermal burn injury
- Figure 32 – Model for absence of a thermal hazard
- Figure 33 – Model for presence of a thermal hazard with a physical safeguard in place
- Figure 34 – Model for presence of a thermal hazard with behavioural safeguard in place
- Figure 35 – Graphical representation of LAeq,T
- Figure 36 – Overview of operating modes
- Figure 37 – Voltage-current characteristics (typical data)
- Figure 38 – Current limit curves
- Figure 39 – Example of a dummy battery circuit
- Figure 40 – Example of a circuit with two power sources
- Figure A.1 – Installation has poor earthing and bonding –Equipment damaged (from ITUT K.66)
- Figure A.2 – Installation has poor earthing and bonding – Using main earth bar for protection against lightning strike (from ITU-T K.66)
- Figure A.3 – Installation with poor earthing and bonding, using a varistorand a GDT for protection against a lightning strike
- Figure A.4 – Installation with poor earthing and bonding – Equipment damaged (TV set)
- Figure A.5 – Safeguards
- Figure A.6 – Discharge stages
- Figure A.7 – holdover
- Figure A.8 – Discharge
- Figure A.9 – Characteristics
- Figure A.10 – Follow on current pictures
- Figure B.1 – Typical EMC filter schematic
- Figure B.2 – 100 MΩ oscilloscope probes
- Figure B.3 – Combinations of EUT resistance and capacitancefor 1-s time constant
- Figure B.4 – 240 V mains followed by capacitor discharge
- Figure B.5 – Time constant measurement schematic
- Figure B.6 – Worst-case measured time constant values for 100 MΩ and 10 MΩ probes
- Tables [Go to Page]
- Table 1 – General summary of required safeguards
- Table 2 – Time/current zones for a.c. 15 Hz to 100 Hzfor hand to feet pathway (see IEC TS 60479-1:2005, Table 11)
- Table 3 – Time/current zones for d.c. for hand to feet pathway(see IEC TS 60479-1:2005, Table 13)
- Table 4 – Limit values of accessible capacitance (threshold of pain)
- Table 5 – Total body resistances RT for a current path hand to hand, d.c.,for large surface areas of contact in dry condition
- Table 6 – Insulation requirements for external circuits
- Table 7 – Voltage drop across clearance and solid insulation in series
- Table 8 – Examples of application of various safeguards
- Table 9 – Basic safeguards against fire under normal operating conditionsand abnormal operating conditions
- Table 10 – Supplementary safeguards against fire under single fault conditions
- Table 11 – Method 1: Reduce the likelihood of ignition
- Table 12 – Method 2: Control fire spread
- Table 13 – Fire barrier and fire enclosure flammability requirements
- Table 14 – Summary – Fire enclosure and fire barrier material requirements
- Table 15 – Control of chemical hazards
- Table 16 – Protection against radiation
- Table B.1 – 100 MΩ oscilloscope probes
- Table B.2 – Capacitor discharge
- Table B.3 – Maximum Tmeasured values for combinationsof REUT and CEUT for TEUT of 1 s [Go to Page]