Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?

BS IEC 61076-8-108:2023 Connectors for electrical and electronic equipment. Product requirements - Power connectors. Detail specification for 2P 250 A, 1 000 V plus 2P 5 A 50 V rectangular housing shielded connectors with IP65/IP68 degree of protection wh, 2023
- undefined
- English [Go to Page]
- CONTENTS
- FOREWORD
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Technical information [Go to Page]
- 4.1 Recommended method of termination [Go to Page]
- 4.1.1 General
- 4.1.2 Number of contacts and contact cavities
- 4.2 Ratings and characteristics
- 4.3 Systems of levels [Go to Page]
- 4.3.1 Performance levels
- 4.3.2 Compatibility levels
- 4.4 Classification into climatic categories
- 4.5 Clearance and creepage distance
- 4.6 Current-carrying capacity
- Tables [Go to Page]
- Table 1 – Climatic category
- 4.7 Marking
- 5 Dimensional information [Go to Page]
- 5.1 General
- 5.2 Isometric view and common features [Go to Page]
- 5.2.1 Isometric view of free connectors (Figure 1)
- 5.2.2 Isometric view of fixed connectors (Figure 2)
- 5.3 Engagement (mating) information [Go to Page]
- 5.3.1 General
- Figures [Go to Page]
- Figure 1 – Free connector isometric view
- Figure 2 – Fixed connector isometric view [Go to Page]
- 5.3.2 Perpendicular to the engaging (mating) direction
- 5.3.3 Inclination
- 5.4 Free connectors [Go to Page]
- 5.4.1 Dimensions (Figure 3, Table 2, Figure 4, Table 3, Table 4)
- Figure 3 – Free connector
- Table 2 – Free connector dimensions
- Figure 4 – Free connector codings
- Table 3 – Free connector codings dimensions (codings 1 and 2) [Go to Page]
- 5.4.2 Terminations
- Table 4 – Free connector codings dimensions (codings 3 and 4)
- 5.5 Fixed connectors [Go to Page]
- 5.5.1 Dimensions (Figure 5, Table 5, Figure 6, Table 6, Table 7)
- Figure 5 – Fixed connector
- Table 5 – Fixed connector dimensions
- Figure 6 – Fixed connector codings [Go to Page]
- 5.5.2 Terminations
- 5.6 Accessories
- 5.7 Mounting information
- 5.8 Gauges – Sizing gauges and retention force gauges
- Table 6 – Fixed connector codings dimensions (codings 1 and 2)
- Table 7 – Fixed connector codings dimensions (codings 3 and 4)
- 6 Technical characteristics [Go to Page]
- 6.1 Classification into climatic categories
- 6.2 Electrical characteristics [Go to Page]
- 6.2.1 Clearance and creepage distance
- 6.2.2 Voltage proof
- Figure 7 – Gauge for signal contacts
- Figure 8 – Gauge for power contacts
- Table 8 – Gauge dimensions [Go to Page]
- 6.2.3 Contact resistance
- 6.2.4 Housing (shell) electrical continuity and shielding effectiveness
- 6.2.5 Insulation resistance
- 6.2.6 Current-carrying capacity
- Table 9 – Voltage proof [Go to Page]
- 6.2.7 Electrical load and temperature
- 6.3 Mechanical characteristics [Go to Page]
- 6.3.1 Mechanical operation
- Figure 9 – Current-temperature derating (70 mm2 wire size) [Go to Page]
- 6.3.2 Effectiveness of connector coupling devices
- 6.3.3 Gauge retention force (resilient contact)
- 6.3.4 Engaging and separating forces
- 6.3.5 Contact retention in insert
- 6.4 Dynamic stress tests [Go to Page]
- 6.4.1 Vibration (sine)
- 6.4.2 Shock
- 6.4.3 Free fall (repeated)
- 6.4.4 IP degree of protection
- 6.4.5 Glow-wire flammability test method for end-products (GWEPT)
- Table 10 – Vibration
- 6.5 Climatic tests [Go to Page]
- 6.5.1 Damp heat, steady state
- 6.5.2 Rapid change of temperature
- 6.5.3 Corrosion, salt mist
- 6.5.4 Dry heat
- 6.5.5 Cold
- 6.5.6 Low air pressure
- 6.6 Environmental aspects [Go to Page]
- 6.6.1 Marking of insulation material (plastic)
- 6.6.2 Design/use of material
- 7 Test schedule [Go to Page]
- 7.1 General
- 7.2 Test schedules [Go to Page]
- 7.2.1 Basic (minimum) test schedule
- 7.2.2 Full test schedule
- Table 11 – Number of test specimens
- Table 12 – Test group P
- Table 13 – Test group AP
- Table 14 – Test group BP
- Table 15 – Test group CP
- Table 16 – Test group DP
- Table 17 – Test group EP
- Table 18 – Test group GP
- Table 19 – Test group HP
- Table 20 – Test group JP
- Table 21 – Test group KP
- 7.3 Test procedures and measurement methods
- 7.4 Pre-conditioning
- 7.5 Wiring and mounting of test specimens [Go to Page]
- 7.5.1 Wiring
- 7.5.2 Mounting [Go to Page]