eLibrary >
BS EN ISO 19085-12:2021+A11:2023 Woodworking machines - Safety - Part 12: Tenoning/profiling machines >
Expand All
TOC Search:
BS EN ISO 19085-12:2021+A11:2023 Woodworking machines - Safety - Part 12: Tenoning/profiling machines, 2023
- undefined [Go to Page]
- Foreword
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 List of significant hazards
- 5 Safety requirements and measures for controls
- 5.1 Safety and reliability of control systems
- 5.2 Control devices
- 5.2.1 General
- 5.2.2 Additional requirements for single end tenoning machines with manual feed sliding table
- 5.2.3 Additional requirements for single end tenoning machines with mechanical feed sliding table
- 5.2.4 Additional requirements for single end tenoning and/or profiling machines with mechanical feed
- 5.2.5 Additional requirements for double end machines
- 5.2.6 Additional requirements for angular systems for tenoning and profiling with mechanical feed
- 5.3 Start
- 5.3.1 Machines with manual feed
- 5.3.2 Machines with mechanical feed
- 5.3.3 Laser marking unit
- 5.4 Safe stops
- 5.4.1 General
- 5.4.2 Normal stop
- 5.4.3 Operational stop
- 5.4.4 Emergency stop
- 5.5 Braking function of tool spindles
- 5.6 Mode selection
- 5.6.1 General
- 5.6.2 Adjustment mode (MODE 2)
- 5.7 Spindle speed changing
- 5.7.1 Spindle speed changing by changing belts on the pulleys
- 5.7.2 Spindle speed changing by incremental speed change motor
- 5.7.3 Infinitely variable speed by frequency inverter
- 5.8 Failure of any power supply
- 5.9 Manual reset control
- 5.10 Enabling control
- 5.11 Machine moving parts limited speed monitoring
- 5.12 Time delay
- 5.13 Tele-service
- 6 Safety requirements and measures for protection against mechanical hazards
- 6.1 Stability
- 6.1.1 Stationary machines
- 6.1.2 Displaceable machines
- 6.2 Risk of break-up during operation
- 6.3 Tool holder and tool design
- 6.3.1 General
- 6.3.2 Spindle locking
- 6.3.3 Circular saw blade fixing devices
- 6.3.4 Flange dimensions for circular saw blades
- 6.3.5 Spindle rings
- 6.4 Braking
- 6.4.1 Braking of tool spindle
- 6.4.2 Maximum run-down time
- 6.4.3 Brake release
- 6.5 Safeguards
- 6.5.1 Fixed guards
- 6.5.2 Interlocking moveable guards
- 6.5.3 Hold-to-run control
- 6.5.4 Two hand control
- 6.5.5 Electro-sensitive protective equipment (ESPE)
- 6.5.6 Pressure sensitive protective equipment (PSPE)
- 6.6 Prevention of access to moving parts
- 6.6.1 General
- 6.6.2 Guarding of tools
- 6.6.3 Guarding of drives
- 6.6.4 Guarding of shearing and/or crushing zones
- 6.7 Impact hazard
- 6.8 Clamping devices
- 6.8.1 Single end tenoning machines with sliding table
- 6.8.2 Machines other than single end tenoning machines with sliding table
- 6.9 Measures against ejection
- 6.9.1 General
- 6.9.2 Guards materials and characteristics
- 6.9.3 Devices to minimize the possibility or effect of ejection or kickback
- 6.10 Work-piece support and guides
- 6.10.1 Single end tenoning machines with sliding table
- 6.10.2 Single end tenoning and/or profiling machines with mechanical feed
- 6.10.3 Double end tenoning and/or profiling machines with mechanical feed
- 6.10.4 Angular systems for tenoning and profiling with mechanical feed
- 6.10.5 Work-piece returner
- 7 Safety requirements and measures for protection against other hazards
- 7.1 Fire
- 7.2 Noise
- 7.2.1 Noise reduction at the design stage
- 7.2.2 Noise emission measurement
- 7.3 Emission of chips and dust
- 7.4 Electricity
- 7.4.1 General
- 7.4.2 Displaceable machines
- 7.5 Ergonomics and handling
- 7.6 Lighting
- 7.7 Pneumatics
- 7.8 Hydraulics
- 7.9 Electromagnetic compatibility
- 7.10 Laser
- 7.11 Static electricity
- 7.12 Errors of fitting
- 7.13 Isolation
- 7.14 Maintenance
- 7.15 Heat
- 7.16 Substances
- 8 Information for use
- 8.1 Warning devices
- 8.2 Marking
- 8.2.1 General
- 8.2.2 Additional markings
- 8.3 Instruction handbook
- 8.3.1 General
- 8.3.2 Additional information
- Annex A (informative) Performance levels required
- Annex B (normative) Tests for braking function
- Annex C (normative) Stability test for displaceable machines
- Annex D (normative) Impact test for guards
- Annex E (normative) Noise emission measurement for single end profiling machines (not in ISO 7960:1995)
- Bibliography [Go to Page]
