Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?
BS EN ISO 10439-1:2015 Petroleum, petrochemical and natural gas industries. Axial and centrifugal compressors and expander-compressors - General requirements, 2015
- 64_e_stf.pdf [Go to Page]
- Contents Page
- Foreword
- C10439-1e.pdf [Go to Page]
- Foreword
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms, abbreviated terms and definitions
- 3.1 Terms and definitions
- 3.2 Abbreviated terms
- 4 General
- 4.1 Dimensions and units
- 4.2 Statutory requirements
- 4.3 Unit responsibility
- 4.4 Basic design
- 4.4.1 General
- 4.4.2 Speed requirements
- 4.5 Materials
- 4.5.1 General
- 4.5.2 Castings
- 4.5.3 Forgings
- 4.5.4 Welding
- 4.6 Casings
- 4.6.1 Pressure-containing casings
- 4.6.2 Casing repairs and inspections
- 4.6.3 Material inspection of pressure-containing parts
- 4.6.4 Pressure casing connections
- 4.6.5 Casing support structures
- 4.6.6 External forces and moments
- 4.6.7 Guide vanes, stators, and stationary internals
- 4.7 Rotating elements
- 4.8 Dynamics
- 4.8.1 General
- 4.8.2 Lateral analysis
- 4.8.3 Unbalanced rotor response verification test
- 4.8.4 Additional testing
- 4.8.5 Level 1 stability analysis
- 4.8.6 Level II stability analysis
- 4.8.7 Torsional analysis
- 4.8.8 Vibration and balancing
- 4.9 Bearings and bearing housings
- 4.9.1 General
- 4.9.2 Hydrodynamic radial bearings
- 4.9.3 Hydrodynamic thrust bearings
- 4.9.4 Bearing housings
- 4.10 Shaft and seals
- 4.10.1 General
- 4.10.2 Clearance seals
- 4.10.3 Oil seals
- 4.10.4 Self-acting dry gas seal
- 4.11 Integral gearing
- 4.12 Nameplates and rotation arrows
- 5 Accessories
- 5.1 Drivers and gearing
- 5.2 Couplings and guards
- 5.3 Lubrication and sealing systems
- 5.4 Mounting plates
- 5.4.1 General
- 5.4.2 Baseplates
- 5.4.3 Soleplates and sub-soleplates
- 5.5 Controls and instrumentation
- 5.5.1 General
- 5.5.2 Control systems
- 5.5.3 Instrument and control panels
- 5.5.4 Instrumentation
- 5.5.5 Alarms, shutdowns, and control systems
- 5.5.6 Electrical systems
- 5.5.7 Vibration, position, and bearing temperature detectors
- 5.6 Piping and appurtenances
- 5.6.1 General
- 5.6.2 Instrument piping
- 5.6.3 Process piping
- 5.7 Special tools
- 6 Inspection, testing, and preparation for shipment
- 6.1 General
- 6.2 Inspection
- 6.2.1 General
- 6.2.2 Material inspection
- 6.3 Testing
- 6.3.1 General
- 6.3.2 Hydrostatic test
- 6.3.3 Overspeed test
- 6.3.4 Dry gas seals
- 6.3.5 Mechanical running test
- 6.3.6 Assembled machine gas leakage test
- 6.3.7 Optional tests
- 6.4 Preparation for shipment
- 7 Supplier’s data
- 7.1 General
- 7.2 Proposals
- 7.2.1 General
- 7.2.2 Drawings
- 7.2.3 Technical data
- 7.2.4 Curves
- 7.2.5 Optional tests
- 7.3 Contract data
- 7.3.1 General
- 7.3.2 Curves and datasheets
- 7.3.3 Progress reports
- 7.3.4 Parts lists and recommended spares
- 7.3.5 Installation, operation, maintenance, and technical data manuals
- Annex A
(normative)
Procedure for the determination of residual unbalance
- Annex B
(informative)
Typical shaft end seals
- Annex C
(normative)
Requirements for lateral analysis reports
- Annex D
(normative)
Requirements for torsional analysis reports
- Annex E
(normative)
Magnetic bearings
- Annex F
(normative)
Dry gas seal testing at manufacturer’s shop
- Annex G
(informative)
Guidelines for anti-surge systems
- Annex H
(informative)
Typical bid tab template
- Bibliography [Go to Page]