Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?
BS EN IEC 60384-11:2019 Fixed capacitors for use in electronic equipment - Sectional specification. Fixed polyethylene-terephthalate film dielectric metal foil DC capacitors, 2020
- undefined
- Annex ZA(normative)Normative references to international publicationswith their corresponding European publications
- English [Go to Page]
- CONTENTS
- FOREWORD
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Preferred ratings and characteristics [Go to Page]
- 4.1 Preferred climatic categories
- 4.2 Preferred values of ratings [Go to Page]
- 4.2.1 Nominal capacitance (CN)
- 4.2.2 Tolerance on nominal capacitance
- 4.2.3 Nominal capacitance with associated tolerance values
- 4.2.4 Rated voltage (UR)
- Tables [Go to Page]
- Table 1 – Preferred combinations of capacitance series and tolerance [Go to Page]
- 4.2.5 Category voltage (UC)
- 4.2.6 Rated temperature
- 5 Test and measurement procedures, and performance requirements [Go to Page]
- 5.1 Visual examination and check of dimensions [Go to Page]
- 5.1.1 General
- 5.1.2 Examination methods
- 5.1.3 Requirements
- 5.2 Electrical tests [Go to Page]
- 5.2.1 Voltage proof
- 5.2.2 Capacitance
- 5.2.3 Tangent of loss angle (tan δ )
- Table 2 – Test voltages [Go to Page]
- 5.2.4 Insulation resistance
- Table 3 – Insulation resistance [Go to Page]
- 5.2.5 Characteristics depending on temperature (if required in the detail specification)
- Table 4 – Correction factor dependent on test temperature
- Table 5 – Characteristics at lower category temperature
- Table 6 – Characteristics at upper category temperature
- 5.3 Robustness of terminations [Go to Page]
- 5.3.1 General
- 5.3.2 Initial inspections
- 5.3.3 Final inspections and requirements
- 5.4 Resistance to soldering heat [Go to Page]
- 5.4.1 General
- 5.4.2 Initial inspections
- 5.4.3 Preconditioning
- 5.4.4 Test Conditions
- 5.4.5 Final inspections, measurements and requirements
- 5.5 Solderability [Go to Page]
- 5.5.1 General
- 5.5.2 Preconditioning
- 5.5.3 Test conditions
- 5.5.4 Final inspections and measurements
- 5.6 Rapid change of temperature [Go to Page]
- 5.6.1 General
- 5.6.2 Initial inspections
- 5.6.3 Test conditions
- 5.6.4 Final inspections, measurements and requirements
- 5.7 Vibration [Go to Page]
- 5.7.1 General
- 5.7.2 Initial inspections
- 5.7.3 Mounting
- 5.7.4 Test conditions
- 5.7.5 Final inspections and requirements
- 5.8 Bump (repetitive shock) [Go to Page]
- 5.8.1 General
- 5.8.2 Mounting
- 5.8.3 Initial measurements
- 5.8.4 Test conditions
- 5.8.5 Final inspection, measurements and requirements
- 5.9 Shock [Go to Page]
- 5.9.1 General
- 5.9.2 Mounting
- 5.9.3 Initial measurements
- 5.9.4 Test conditions
- 5.9.5 Final inspections, measurements and requirements
- 5.10 Climatic sequence [Go to Page]
- 5.10.1 General
- 5.10.2 Initial measurements
- 5.10.3 Dry heat
- 5.10.4 Damp heat, cyclic, Test Db, first cycle
- 5.10.5 Cold
- 5.10.6 Low air pressure (if required)
- Table 7 – Acceleration and duration of the pulse [Go to Page]
- 5.10.7 Damp heat, cyclic, Test Db, remaining cycles
- 5.10.8 Recovery
- 5.10.9 Final inspections, measurements and requirements
- 5.11 Damp heat, steady state [Go to Page]
- 5.11.1 General
- 5.11.2 Initial inspections
- 5.11.3 Test conditions
- 5.11.4 Recovery
- 5.11.5 Final inspections, measurements and requirements
- 5.12 Endurance [Go to Page]
- 5.12.1 General
- 5.12.2 Initial inspections
- 5.12.3 Test conditions
- 5.12.4 Final inspections, measurements and requirements
- 5.13 Component solvent resistance (if applicable)
- 5.14 Solvent resistance of the marking (if applicable)
- 6 Marking [Go to Page]
- 6.1 General
- Table 8 – Endurance test
- 6.2 Information for marking
- 6.3 Marking on capacitors
- 6.4 Marking on packaging
- 6.5 Additional marking
- 7 Information to be given in the detail specification [Go to Page]
- 7.1 General
- 7.2 Outline drawing and dimensions
- 7.3 Mounting
- 7.4 Ratings and characteristics [Go to Page]
- 7.4.1 General
- 7.4.2 Nominal capacitance range
- 7.4.3 Particular characteristics
- 7.4.4 Soldering
- 7.5 Marking
- 8 Quality assessment procedures [Go to Page]
- 8.1 Primary stage of manufacture
- 8.2 Structurally similar components
- 8.3 Certified records of released lots
- 8.4 Qualification approval [Go to Page]
- 8.4.1 General
- 8.4.2 Qualification approval on the basis of the fixed sample size procedure
- Table 9 – Fixed sample size test plan for qualification approval assessment level EZ
- Table 10 – Test schedule for qualification approval (1 of 5)
- 8.5 Quality conformance inspection [Go to Page]
- 8.5.1 Formation of inspection lots
- 8.5.2 Test schedule
- 8.5.3 Delayed delivery
- 8.5.4 Assessment levels
- Table 11 – Lot-by-lot inspection
- Table 12 – Periodic inspection
- Annex X (informative) Cross-references to the previous edition of this document [Go to Page]
- Table X.1 – Cross-references
- Bibliography [Go to Page]
