Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?

BS EN 61169-53:2016 Radio-frequency connectors - Sectional specification for RF coaxial connectors with inner diameter of outer conductor 16 mm with screw lock. Characteristic impedance 50 O (Type S7-16), 2016
- 30311696-VOR.pdf [Go to Page]
- English [Go to Page]
- CONTENTS
- FOREWORD
- 1 Scope
- 2 Normative references
- 3 Mating face and gauge information [Go to Page]
- 3.1 Dimensions – General connectors – Grade 2 [Go to Page]
- 3.1.1 Connector with pin-centre contact
- 3.1.2 Connector with socket centre contact
- 3.2 Gauges [Go to Page]
- 3.2.1 Gauge pin for socket-centre contact
- 3.2.2 Test procedure
- 3.3 Dimensions – Standard test connectors – Grade 0 [Go to Page]
- 3.3.1 Connector with pin-centre contact
- 3.3.2 Standard test connector with socket-centre contact
- 4 Quality assessment procedures [Go to Page]
- 4.1 General
- 4.2 Ratings and characteristics (see Clause 5 of IEC 61169-1:2013)
- 4.3 Test schedule and inspection requirements [Go to Page]
- 4.3.1 Acceptance tests
- 4.3.2 Periodic tests
- 4.4 Procedures for the quality conformance [Go to Page]
- 4.4.1 Quality conformance inspection
- 4.4.2 Qualification approval and its maintenance
- 5 Instructions for preparation of detail specifications [Go to Page]
- 5.1 General
- 5.2 Identification of the component
- 5.3 Performances
- 5.4 Marking, ordering information and related matters
- 5.5 Selection of tests, test conditions and severities
- 5.6 Blank detail specification pro-forma for type S7-16 connector
- 6 Marking [Go to Page]
- 6.1 Marking of component
- 6.2 Marking and contents of package
- Figures [Go to Page]
- Figure 1 – Connector with pin-centre contact (for dimensions, see Table 1)
- Figure 2 – Connector with socket-centre contact (for dimensions, see Table 2)
- Figure 3 – Gauge pin for socket-centre contact (for dimensions, see Table 3)
- Figure 4 – Connector with pin-centre contact (for dimensions, see Table 4)
- Figure 5 – Connector with socket-centre contact (for dimensions, see Table 5)
- Tables [Go to Page]
- Table 1 – Dimensions of connector with pin-centre contact
- Table 2 – Dimensions of connector with socket centre contact
- Table 3 – Dimensions of gauge pin for socket-centre contact
- Table 4 – Dimensions of connector with pin-centre contact
- Table 5 – Dimensions of connector with socket-centre contact
- Table 6 – Rating and characteristics
- Table 7 – Acceptance tests
- Table 8 – Periodic tests
- Français [Go to Page]
- SOMMAIRE
- AVANT-PROPOS
- 1 Domaine d’application
- 2 Références normatives
- 3 Informations relatives aux éléments d’accouplement et aux calibres [Go to Page]
- 3.1 Dimensions – Connecteurs à usage général – Classe 2 [Go to Page]
- 3.1.1 Connecteur avec contact central mâle
- 3.1.2 Connecteur avec contact central femelle
- 3.2 Calibres [Go to Page]
- 3.2.1 Broche calibrée pour contact central femelle
- 3.2.2 Procédure d’essai
- 3.3 Dimensions- connecteurs d'essais normalisés – Classe 0 [Go to Page]
- 3.3.1 Connecteur avec contact central mâle
- 3.3.2 Connecteur d’essai de référence avec contact central femelle
- 4 Procédures d'assurance de la qualité [Go to Page]
- 4.1 Généralités
- 4.2 Valeurs assignées et caractéristiques (voir l’Article 5 de l'IEC 61169-1:2013)
- 4.3 Programme d'essais et exigences de contrôle [Go to Page]
- 4.3.1 Essais d'acceptation
- 4.3.2 Essais périodiques
- 4.4 Procédures de conformité de la qualité [Go to Page]
- 4.4.1 Contrôle de conformité de la qualité
- 4.4.2 Homologation et maintenance
- 5 Instructions en vue de l'établissement des spécifications particulières [Go to Page]
- 5.1 Généralités
- 5.2 Identification du composant
- 5.3 Performances
- 5.4 Marquages, informations relatives aux commandes et sujets connexes
- 5.5 Choix des essais, conditions et sévérités des essais
- 5.6 Spécification particulière-cadre pro forma pour connecteur de type S7-16
- 6 Marquage [Go to Page]
- 6.1 Marquage du composant
- 6.2 Marquage et contenu des emballages
- Figures [Go to Page]
- Figure 1 – Connecteur avec contact central mâle (pour les dimensions, voir le Tableau 1)
- Figure 2 – Connecteur avec contact central femelle (pour les dimensions, voir le Tableau 2)
- Figure 3 – Broche calibrée pour contact central femelle (pour les dimensions, voir le Tableau 3)
- Figure 4 – Connecteur avec contact central mâle (pour les dimensions, voir le Tableau 4)
- Figure 5 – Connecteur avec contact central femelle (pour les dimensions, voir le Tableau 5)
- Tableaux [Go to Page]
- Tableau 1 – Dimensions du connecteur avec contact central mâle
- Tableau 2 – Dimensions du connecteur avec contact central femelle
- Tableau 3 – Dimensions de la broche calibrée pour contact femelle
- Tableau 4 – Dimensions du connecteur avec contact central mâle
- Tableau 5 – Dimensions du connecteur avec contact central femelle
- Tableau 6 – Valeurs assignées et caractéristiques
- Tableau 7 – Essais d’acceptation
- Tableau 8 – Essais périodiques [Go to Page]