Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?
BS EN 60384-13:2006 Fixed capacitors for use in electronic equipment - Sectional specification. Fixed polypropylene film dielectric metal foil d.c. capacitors, 2010
- BS EN 60384-13 word copy.pdf [Go to Page]
- 1 General [Go to Page]
- 1.1 Scope
- 1.2 Object
- 1.3 Normative references
- 1.4 Information to be given in a detail specification [Go to Page]
- 1.4.1 Outline drawing and dimensions
- 1.4.2 Mounting
- 1.4.3 Ratings and characteristics [Go to Page]
- 1.4.3.1 Rated capacitance range
- 1.4.3.2 Particular characteristics
- 1.4.3.3 Soldering
- 1.4.4 Marking
- 1.5 Terms and definitions
- 1.6 Marking
- 2 Preferred ratings and characteristics [Go to Page]
- 2.1 Preferred characteristics [Go to Page]
- 2.1.1 Preferred climatic categories
- 2.2 Preferred values of ratings [Go to Page]
- 2.2.1 Rated capacitance (CR)
- 2.2.2 Tolerances on rated capacitance
- 2.2.3 Rated voltage (UR)
- 2.2.4 Stability classes in relation to temperature coefficients and change of capacitance
- 2.2.5 Category voltage (UC)
- 2.2.6 Rated temperature
- 3 Quality assessment procedures [Go to Page]
- 3.1 Primary stage of manufacture
- 3.2 Structurally similar components
- 3.3 Certified records of released lots
- 3.4 Qualification approval [Go to Page]
- 3.4.1 Qualification approval on the basis of the fixed sample size procedure [Go to Page]
- 3.4.1.1 Sampling
- 3.4.1.2 Tests
- 3.5 Quality conformance inspection [Go to Page]
- 3.5.1 Formation of inspection lots
- 3.5.2 Test schedule
- 3.5.3 Delayed delivery
- 3.5.4 Assessment levels
-
- 4 Test and measurement procedures [Go to Page]
- 4.1 Visual examination and check of dimensions
- 4.2 Electrical tests [Go to Page]
- 4.2.1 Voltage proof [Go to Page]
- 4.2.1.1 Test circuit
- 4.2.2 Capacitance
- 4.2.3 Tangent of loss angle (tan δ) [Go to Page]
- 4.2.3.1 Measuring conditions
- 4.2.3.2 Requirements
- 4.2.4 Insulation resistance
- 4.2.5 Characteristics depending on temperature [Go to Page]
- 4.2.5.1 Measuring conditions
- 4.2.7 Outer foil termination (if required)
- 4.3 Robustness of terminations [Go to Page]
- 4.3.1 Initial measurements
- 4.4 Resistance to soldering heat [Go to Page]
- 4.4.1 Conditions
- 4.4.2 Final inspection, measurements and requirements
- 4.5 Solderability [Go to Page]
- 4.5.1 Test conditions: No ageing
- 4.5.2 Requirements
- 4.6 Rapid change of temperature [Go to Page]
- 4.6.1 Initial measurements
- 4.6.2 Number of cycles: 5
- 4.7 Vibration [Go to Page]
- 4.7.1
- 4.7.2 Final inspection, measurements and requirements
- 4.8 Bump [Go to Page]
- 4.8.1 Initial measurements
- 4.8.2
- 4.8.3 Final inspection, measurements and requirements
- 4.9 Shock [Go to Page]
- 4.9.1 Initial measurements
- 4.9.3 Final inspection, measurements and requirements
- 4.10 Climatic sequence [Go to Page]
- 4.10.1 Initial measurements
- 4.10.2 Dry heat
- 4.10.3 Damp heat, cyclic, Test Db, first cycle
- 4.10.4 Cold
- 4.10.5 Low air pressure [Go to Page]
- 4.10.5.1
- 4.10.5.2
- 4.10.5.3 Final inspection and requirements
- 4.10.6 Damp heat, cyclic, Test Db, remaining cycles
- 4.11 Damp heat, steady state [Go to Page]
- 4.11.1 Initial measurements
- 4.12 Endurance [Go to Page]
- 4.12.1 Initial measurements
- 4.12.5 Final inspection, measurements and requirements
- 4.13 Component solvent resistance
- 4.14 Solvent resistance of the marking [Go to Page]
