Already a subscriber? 
MADCAD.com Free Trial
Sign up for a 3 day free trial to explore the MADCAD.com interface, PLUS access the
2009 International Building Code to see how it all works.
If you like to setup a quick demo, let us know at support@madcad.com
or +1 800.798.9296 and we will be happy to schedule a webinar for you.
Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?
ASME A112.19.2 /CSA B45.1 Ceramic Plumbing Fixtures, 2013
- Standards Update Service
- Contents
- Committee Roster
- CSA Technical Committee on Plumbing Fixtures (B45)
- CSA/ASME Harmonization Task Group on Plumbing Fixtures (B45-JHTG)
- Preface
- 0 Introduction
- 1 Scope
- 2 Reference publications
- 3 Definitions and abbreviations [Go to Page]
- 3.1 Definitions
- 3.2 Abbreviations
- 4 General requirements [Go to Page]
- 4.1 Dimensions and tolerances
- 4.2 Glazing
- 4.3 Waste fitting openings, drainage, and overflows
- 4.4 Off-the-floor plumbing fixture supports
- 4.5 Non-vitreous china plumbing fixtures
- 4.6 Additional requirements for water closets
- 4.7 Additional requirements for urinals
- 4.8 Additional requirements for lavatories, sinks, and bidets
- 4.9 Additional requirements for bathtubs and shower bases
- 4.10 Additional requirements for drinking fountains
- 4.11 Accessible design fixtures
- 5 Flushing devices used with fixtures [Go to Page]
- 5.1 General
- 5.2 Gravity flush tanks
- 5.3 Pressurized flushing devices
- 5.4 Plastic water closet tanks
- 5.5 Electrical components of electro-hydraulic water closets
- 5.6 Dual-flush water closets
- 6 Tests — Materials, finishes, structural integrity, and seals [Go to Page]
- 6.1 Water absorption test
- 6.2 Crazing test
- 6.3 Surface examination
- 6.4 Warpage test
- 6.5 Field-installed tiling-flange seal test
- 6.6 Overflow test
- 6.7 Structural integrity tests for wall-mounted plumbing fixtures
- 6.8 Structural integrity test for bathtubs, shower bases, and non-vitreous service sinks
- 6.9 Joint seal test
- 6.10 Auger test
- 6.11 Condensation-free (insulated) tank test
- 7 Water closet tests [Go to Page]
- 7.1 General
- 7.2 Trap seal depth determination test
- 7.3 Trap seal restoration test
- 7.4 Water consumption test
- 7.5 Granule and ball test
- 7.6 Surface wash test
- 7.7 Mixed media test
- 7.8 Drain line transport characterization test
- 7.9 Overflow test for gravity flush tanks
- 7.10 Waste extraction test
- 7.11 Consistent water level test
- 7.12 Fill valve shutoff integrity test with increased water pressure
- 7.13 Adjustability test for tank-type gravity water closets with original equipment
- 7.14 Adjustability test for tank-type gravity water closets with aftermarket closure seals
- 8 Urinal tests [Go to Page]
- 8.1 General
- 8.2 Test apparatus and general instructions
- 8.3 Trap seal depth determination test
- 8.4 Surface wash test
- 8.5 Dye test
- 8.6 Water consumption test
- 8.7 Tests for non-water-consuming urinals
- 9 Markings, packaging, and installation instructions and other literature [Go to Page]
- 9.1 General
- 9.2 Non-standard fixtures
- 9.3 Additional markings for water closets and urinals
- 9.4 Field-installed flanges
- 9.5 Packaging
- 9.6 Installation instructions and other literature
- Annex A (informative) Suggested formats for reporting test results
- Annex B (informative) Unit conversion criteria
- Tables [Go to Page]
- Table 1 Permitted defects in water closets and urinals
- Table 2 Permitted defects in lavatories and drinking fountains
- Table 3 Integral trap diameter requirements for urinals, mm (in)
- Table 4 Minimum dimensions for urinals, mm (in)
- Table 5 Static test pressures for water closets, kPa (psi)
- Table 6 Static test pressures for urinals, kPa (psi)
- Figures [Go to Page]
- Figure 1 Waste outlet dimensions
- Figure 2 Outlet dimensions for floor-mounted bottom-outlet water closets
- Figure 3 Outlet dimensions for rear-outlet and rear-spigot-outlet water closet bowls
- Figure 4 Bolt hole spacing for wall-mounted water closet bowls
- Figure 5 Roughing-in and seat bolt hole dimensions for water closets
- Figure 6 Water closet bowl rim profiles
- Figure 7 Supply fitting opening and mounting surface dimensions
- Figure 8 Dimensions for bathtubs
- Figure 9 Clearance for drinking fountains
- Figure 10 Gravity flush tank valve openings
- Figure 11 Standardization of water supply system for testing gravity and flushometer tank water closets
- Figure 12 Standardization of water supply system for testing flushometer valve water closets and urinals
- Figure 14 Suggested drain line transport characterization test assembly [Go to Page]
